40844
13
Zoom out
Zoom in
Previous page
1/40
Next page
English – 13
GENERAL SAFETY PRECAUTIONS
Adjustment of depth gauge setting
The cutting teeth should be newly sharpened before
adjusting the depth gauge setting. We recommend that
you adjust the depth gauge setting every third time you
sharpen the cutting teeth. NOTE! This recommendation
assumes that the length of the cutting teeth is not reduced
excessively.
You will need a flat file and a depth gauge tool. We
recommend that you use our depth gauge tool to acheive
the correct depth gauge setting and bevel for the depth
gauge.
Place the depth gauge tool over the chain. Detailed
information regarding the use of the depth gauge tool, will
be found on the package for the depth gauge tool. Use the
flat file to file off the tip of the depth gauge that protrudes
through the depth gauge tool. The depth gauge setting is
correct when you no longer feel resistance as you draw
the file along the depth gauge tool.
Tensioning the chain
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take up the
slack.
Check the chain tension every time you refuel. NOTE! A new
chain has a running-in period during which you should check
the tension more frequently.
Tension the chain as tightly as possible, but not so tight that
you cannot pull it round freely by hand.
Undo the bar nuts that hold the clutch cover/chain brake.
Use the combination spanner. Then tighten the bar nuts
by hand as tight as you can.
Raise the tip of the bar and stretch the chain by tightening
the chain tensioning screw using the combination
spanner. Tighten the chain until it does not sag from the
underside of the bar.
Use the combination spanner to tighten the bar nuts while
lifting the tip of the bar at the same time. Check that you
can pull the chain round freely by hand and that it does not
sag from the underside of the bar.
The position of the chain tensioning screw on our chain saws
varies from model to model. See instructions under the
heading What is what? to find out where it is on your model.
Lubricating cutting equipment
Chain oil
Chain oil must demonstrate good adhesion to the chain and
also maintain its flow characteristics regardless of whether it
is warm summer or cold winter weather.
As a chain saw manufacturer we have developed an optimal
chain oil which, with its vegetable oil base, is also
biodegradable. We recommend the use of our own oil for both
maximum chain life and to minimise environmental damage.
If our own chain oil is not available, standard chain oil is
recommended.
Never use waste oil! Using waste oil can be dangerous to
you and damage the machine and environment.
Filling with chain oil
All our chain saws have an automatic chain lubrication
system. On some models the oil flow is also adjustable.
The saw chain oil tank and the fuel tank are designed so
that the fuel runs out before the saw chain oil.
However, this safety feature requires that you use the right
sort of chain oil (if the oil is too thin it will run out before the
fuel), and that you adjust the carburetor as recommended
(a lean mixture may mean that the fuel lasts longer than
the oil) and that you also use the recommended cutting
equipment (a bar that is too long will use more chain oil).
!
WARNING! A slack chain may jump off and
cause serious or even fatal injury.
!
WARNING! Poor lubrication of cutting
equipment may cause the chain to snap,
which could lead to serious, even fatal
injuries.
IMPORTANT! When using vegetable based saw chain oil,
dismantle and clean the groove in the bar and saw chain
before long-term storage. Otherwise there is a risk of the
saw chain oil oxidizing, which will result in the saw chain
becoming stiff and the bar tip sprocket jamming.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 455 Rancher at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 455 Rancher in the language / languages: English as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 455 Rancher

Husqvarna 455 Rancher User Manual - English - 44 pages

Husqvarna 455 Rancher User Manual - German - 84 pages

Husqvarna 455 Rancher User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info