Manual Husqvarna 450e II (page 34 of 120) (English, Portuguese, Spanish)

579278

Zoom out

Zoom in

1/120

• Chain pitch, in. The distance between the drive links

of the saw chain must align with the distance of the

teeth on the bar tip sprocket and drive sprocket.

(Fig. 108)

• Number of drive links. The number of drive links is

decided by the type of guide bar.

(Fig. 109)

• Bar groove width, in/mm. The groove width in guide

bar must be the same as the chain drive links width.

(Fig. 110)

• Chain oil hole and hole for chain tensioner. The

guide bar must align with product.

(Fig. 111)

• Drive link width, mm/in.

(Fig. 112)

General information about how to sharpen the

cutters

Do not use a blunt saw chain. If the saw chain is blunt,

you must apply more pressure to push the guide bar

through the wood. If the saw chain is very blunt, there

will be no wood chips but sawdust.

A sharp saw chain eats through the wood and the wood

chips becomes long and thick.

The cutting tooth (A) and the depth gauge (B) together

makes the cutting part of the saw chain, the cutter. The

difference in height between the two gives the cutting

depth (depth gauge setting).

(Fig. 113)

When you sharpen the cutter, think about the following:

• Filing angle.

(Fig. 114)

• Cutting angle.

(Fig. 115)

• File position.

(Fig. 116)

• Round file diameter.

(Fig. 117)

It is not easy to sharpen a saw chain correctly without

the correct equipment. Use Husqvarna file gauge. This

will help you to keep maximum cutting performance and

the kickback risk at a minimum.

WARNING: The force of the kickback

increases a lot if you do not follow the

sharpening instructions.

Note: Refer to

To sharpen the saw chain on page 33

for

information about sharpening of the saw chain.

To sharpen the cutters

1. Use a round file and a file gauge to sharpen the

cutting teeth. (Fig. 118)

Note: Refer to

Accessories on page 39

for

information about which file and gauge that

Husqvarna recommends for your saw chain.

2. Apply the file gauge correctly on to the cutter. Refer

to the instruction supplied with the file gauge.

3. Move the file from the inner side of the cutting teeth

and out. Decrease the pressure on the pull stroke.

(Fig. 119)

4. Remove material from one side of all the cutting

teeth.

5. Turn the product around and remove material on the

other side.

6. Make sure that all cutting teeth are the same length.

General information about how to adjust the

depth gauge setting

The depth gauge setting (C) decreases when you

sharpen the cutting tooth (A). To keep maximum cutting

performance you must remove filing material from the

depth gauge (B) to receive the recommended depth

gauge setting. See

Accessories on page 39

for

instructions about how to receive the correct depth

gauge setting for your saw chain.

(Fig. 120)

WARNING: The risk of kickback increases if

the depth gauge setting is too large!

To adjust the depth gauge setting

Before you adjust the depth gauge setting or sharpen

the cutters, refer to

To sharpen the cutters on page 34

for instructions. We recommend you to adjust the depth

gauge setting after each third operation that you

sharpen the cutting teeth.

We recommend that you use our depth gauge tool to

receive the correct depth gauge setting and bevel for the

depth gauge.

(Fig. 121)

1. Use a flat file and a depth gauge tool to adjust the

depth gauge setting. Only use Husqvarna depth

gauge tool to get the correct depth gauge setting and

bevel for the depth gauge.

2. Put the depth gauge tool on the saw chain.

Note:

See the package of the depth gauge tool for

more information about how to use the tool.

3. Use the flat file to remove the part of the depth

gauge that extends through the depth gauge tool.

(Fig. 122)

1286 - 002 - 03.06.2020

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 450e II in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 4,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 450e II

Husqvarna 450e II User Manual - German, Dutch, French - 100 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna 450e II Manual

Product: