Manual Husqvarna 445e (page 23 of 36) (English)

477612

Zoom out

Zoom in

1/36

WORKING TECHNIQUES

English – 23

1153136-26 Rev.1 2009-12-29

4 Never use the chain saw above shoulder height

and try not to cut with the tip of the bar. Never use

the chain saw one-handed!

(58)

5 You must have a steady stance in order to have full

control over the chain saw. Never work standing on a

ladder, in a tree or where you do not have ﬁrm ground

to stand on.

(59)

6 Always use a fast cutting speed, i.e. full throttle.

7 Take great care when you cut with the top edge of the

bar, i.e. when cutting from the underside of the object.

This is known as cutting on the push stroke. The chain

tries to push the chain saw back towards the user. If

the saw chain is jamming, the saw may be pushed

back at you.

(60)

8 Unless the user resists this pushing force there is a

risk that the chain saw will move so far backwards that

only the kickback zone of the bar is in contact with the

tree, which will lead to a kickback.

(61)

Cutting with the bottom edge of the bar, i.e. from the

top of the object downwards, is known as cutting on

the pull stroke. In this case the chain saw pulls itself

towards the tree and the front edge of the chain saw

body rests naturally on the trunk when cutting. Cutting

on the pull stroke gives the operator better control

over the chain saw and the position of the kickback

zone.

(62)

9 Follow the instructions on sharpening and maintaining

your bar and chain. When you replace the bar and

chain use only combinations that are recommended

by us. See instructions under the headings Cutting

equipment and Technical data.

Basic cutting technique

General

• Always use full throttle when cutting!

• Reduce the speed to idle after every cut (running the

engine for too long at full throttle without any load, i.e.

without any resistance from the chain during cutting,

can lead to serious engine damage).

• Cutting from above = Cutting on the pull stroke.

• Cutting from below = Cutting on the push stroke.

Cutting on the push stroke increases the risk of kickback.

See instructions under the heading How to avoid

kickback.

Terms

Cutting = General term for cutting through wood.

Limbing = Cutting branches off a felled tree.

Splitting = When the object you are cutting breaks off

before the cut is complete.

There are ﬁve important factors you should consider

before making a cut:

1 Make sure the cutting equipment will not jam in the

cut.

(63)

2 Make sure the object you are cutting will not split. (64)

3 Make sure the chain will not strike the ground or any

other object during or after cutting.

(65)

4 Is there a risk of kickback? (4)

5 Do the conditions and surrounding terrain affect how

safely you can stand and move about?

Two factors decide whether the chain will jam or the object

that you are cutting will split: the ﬁrst is how the object is

supported before and after cutting, and the second is

whether it is in tension.

In most cases you can avoid these problems by cutting in

two stages; from the top and from the bottom. You need to

support the object so that it will not trap the chain or split

during cutting.

The following instructions describe how to handle the

commonest situations you are likely to encounter when

using a chain saw.

Limbing

When limbing thick branches you should use the same

approach as for cutting.

Cut difﬁcult branches piece by piece. (66)

Cutting

If you have a pile of logs, each log you attempt to cut

should be removed from the pile, placed on a saw horse

or runners and cut individually.

Remove the cut pieces from the cutting area. By leaving

them in the cutting area, you increase the risk for

inadvertently getting a kickback, as well as increasing the

risk of losing your balance while working.

(67)

The log is lying on the ground. There is little risk of the

chain jamming or the object splitting. However there is a

risk that the chain will touch the ground when you ﬁnish

the cut.

(68)

Cut all the way through the log from above. Avoid letting

the chain touch the ground as you ﬁnish the cut. Maintain

full throttle but be prepared for what might happen.

(69)

If it is possible (can you turn the log?) stop cutting about

2/3 of the way through the log.

WARNING! Never use a chain saw by

holding it with one hand. A chain saw is

not safely controlled with one hand.

Always have a secure, ﬁrm grip around

the handles with both hands.

IMPORTANT! If the chain jams in the cut: stop the

engine! Don’t try to pull the chain saw free. If you do you

may be injured by the chain when the chain saw

suddenly breaks free. Use a lever to open up the cut and

free the chain saw.

WARNING! Never attempt to cut logs

while they are in a pile or when a couple

of logs are lying together. Such

procedures drastically increase the risk

of kickback which can result in a serious

or fatal injury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 445e in the language / languages: English as an attachment in your email.

The manual is 2,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 445e

Husqvarna 445e User Manual - German, Dutch, French - 124 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna 445e Manual

Product: