733797
18
Zoom out
Zoom in
Previous page
1/40
Next page
WARNING: Cut pieces in the work area
increase the risk of kickback and that
you cannot keep your balance.
To use the spiked bumper
1. Push the spiked bumper into the trunk of the tree.
2. Apply full throttle and rotate the product. Keep the
spiked bumper against the trunk. This procedure
makes it easier to apply the force necessary to cut
through the trunk.
To cut a trunk on the ground
1. Cut through the trunk on the pull stroke. Keep full
power but be prepared for sudden accidents.
WARNING: Make sure that the saw
chain does not touch the ground when
you complete the kerf.
2. Cut approximately ⅔ through the trunk and then
stop. Turn the trunk and cut from the opposite side.
To cut a trunk that has support on one end
WARNING:
Make sure that the trunk does
not break during cutting. Obey the
instructions below.
1. Cut on the push stroke approximately ⅓ through the
trunk.
2. Cut through the trunk on the pull stroke until the two
kerfs touch.
To cut a trunk that has support on two ends
WARNING: Make sure that the saw chain
does not get caught in the trunk during
cutting. Obey the instructions below.
1. Cut on the pull stroke approximately ⅓ through the
trunk.
2. Cut through the remaining part of the trunk on the
push stroke to complete the cut.
WARNING: Stop the motor if the saw chain
gets caught in the trunk. Use a lever to open
up the kerf and remove the product. Do not
try to pull the product out by hand. This can
result in injury when the product suddenly
breaks free.
To use the limbing technique
Note:
For thick branches, use the cutting technique.
Refer to
To use the cutting technique on page 17
.
WARNING: There is a high accident risk
when you use the limbing technique. Refer
to
Kickback information on page 15
for
instructions how to prevent kickback.
WARNING: Cut limbs one by one. Be careful
when you remove small limbs and do not cut
bushes or many small limbs at the same
time. Small limbs can get caught in the saw
18 958 - 010 - 24.04.2020
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 330i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 330i in the language / languages: English as an attachment in your email.

The manual is 4,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 330i

Husqvarna 330i User Manual - German, Dutch, French - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info