734088

Husqvarna 129RJ Manual

10
Zoom out
Zoom in
Previous page
1/324
Next page
• Do not smoke near the fuel or the engine.
• Do not put warm objects near the fuel or the engine.
• Do not add the fuel when the engine is on.
• Make sure that the engine is cool before you refuel.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
• Tighten the fuel tank cap carefully or a fire can
occur.
• Move the product at a minimum of 3 m (10 ft) from
the position where you filled the tank before a start.
• Do not put too much fuel in the fuel tank.
• Make sure that a leak cannot occur when you move
the product or fuel container.
• Do not put the product or a fuel container where
there is an open flame, spark or pilot light. Make
sure that the storage area does not contain an open
flame.
• Only use approved containers when you move the
fuel or put the fuel into storage.
• Empty the fuel tank before long-term storage. Obey
the local law on where to dispose fuel.
• Clean the product before long-term storage.
• Remove the spark plug cable before you put the
product into storage to make sure that the engine
does not start accidentally.
S
Safety instructions for maintenance
• If you cannot adjust the idle speed to make the
cutting attachment stop, speak to your service
center. Do not use the product until the product is
correctly adjusted or repaired.
ASSEMBLY
WARNING:
Read the safety chapter before
you assemble the product.
To attach the loop handle
1. Attach the loop handle to the shaft in compliance
with the illustration (Picture 24) and tighten.
2. Make sure that the loop handle attaches between
the arrows on the shaft.
To attach the J-handle
WARNING:
Do not use saw blades when
you install the J-handle. Use only grass
blades/grass cutters or trimmer heads/
plastic blades.
1. Attach the J-handle to the loop handle in compliance
with the illustration (Picture 24) and tighten.
To install the harness clamp
1. Put the top harness clamp on the shaft. Put the low
harness clamp below the shaft.
2. Align the screws in the top and low harness clamp.
3. Install two screws into the screw holes.
4. Tighten the screws to connect the harness clamp.
To install a blade guard, grass blade
and grass cutter
CAUTION:
Only use the approved guard for
the blades. See
ACCESSORIES on page
15
.
1. Attach the blade guard/cutting attachment guard (A)
onto the shaft (Picture 27) and tighten with the bolt.
2. Install the drive disc (B) on the output shaft.
3. Turn the output shaft until one of the holes in the
drive disc aligns with the related hole in the gear
housing.
4. Put the locking pin (C) in the hole to lock the shaft.
5. Put the blade (D), support cup (E) and support
flange (F) on the output shaft.
6. Install the nut (G). Torque the nut to 35-50 Nm
(26-36 ft/lb). Hold the shaft of the wrench near the
blade guard as much as possible. To tighten the nut,
you must turn the wrench in the opposite direction of
rotation.
Note:
Left hand thread.
To install blades and trimmer heads
WARNING:
Only use the approved guard for
the blades. See
ACCESSORIES on page
15
. A defective guard can cause injury.
WARNING:
If you operate the product with a
grass blade, first install the correct
handlebar, blade guard and harness .
WARNING:
If you do not install the the
blades correctly (Picture 26), it can cause
injury.
1. Make sure that the lifted section on the drive disc/
support flange engages correctly in the center hole
of the blades.
2. Install the blades.
10
194 - 002 -
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 129RJ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 129RJ in the language / languages: All languages as an attachment in your email.

The manual is 2,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info