Manual Husqvarna 129R (page 10 of 332) (All languages)

734089

Zoom out

Zoom in

1/332

• If you spill fuel on your clothing, change clothing

immediately.

• Do not get fuel on your body, it can cause injury. If

you get fuel on your body, use a soap and water to

remove the fuel.

• Do not start the engine if you spill oil or fuel on the

product or on your body.

• Do not start the product if the engine has a leak.

Examine the engine for leaks regularly.

• Be careful with fuel. Fuel is flammable and the fumes

are explosive and can cause injuries or death.

• Do not breathe in the fuel fumes, it can cause injury.

Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put warm objects near the fuel or the engine.

• Do not add the fuel when the engine is on.

• Make sure that the engine is cool before you refuel.

• Before you refuel, open the fuel tank cap slowly and

release the pressure carefully.

• Do not add fuel to the engine in an indoor area. Not

sufficient airflow can cause injury or death because

of asphyxiation or carbon monoxide.

• Tighten the fuel tank cap carefully or a fire can

occur.

• Move the product at a minimum of 3 m (10 ft) from

the position where you filled the tank before a start.

• Do not put too much fuel in the fuel tank.

• Make sure that a leak cannot occur when you move

the product or fuel container.

• Do not put the product or a fuel container where

there is an open flame, spark or pilot light. Make

sure that the storage area does not contain an open

flame.

• Only use approved containers when you move the

fuel or put the fuel into storage.

• Empty the fuel tank before long-term storage. Obey

the local law on where to dispose fuel.

• Clean the product before long-term storage.

• Remove the spark plug cable before you put the

product into storage to make sure that the engine

does not start accidentally.

Safety instructions for maintenance

• If you cannot adjust the idle speed to make the

cutting attachment stop, speak to your service

center. Do not use the product until the product is

correctly adjusted or repaired.

ASSEMBLY

WARNING:

Read the safety chapter before

you assemble the product.

To install the handlebar

1. Remove the screw behind the throttle handle.

2. Move the throttle handle to the right side of the

handlebar (Picture 25).

3. Align the hole behind the throttle handle with the

hole in the handlebar.

4. Let the screw go through the holes. Tighten the

screw.

5. Install the mounting components (Picture 25)

between the arrows on the shaft. Tighten with

screws.

To install the harness clamp

1. Put the upper harness clamp above the shaft.

Note:

The upper harness clamp and the lower

harness clamp must be above the arrow on the

shaft.

2. Put the throttle wire in the of lower harness clamp

groove. Put the lower harness clamp with wire in

groove below the shaft.

3. Align the upper and lower harness clamp screw

holes.

4. Attach two screws into the screw holes.

5. Tighten the screws to attach the harness clamp.

To adjust the harness

WARNING:

If you must release from the

product and the harness in an emergency

situation, use the harness release function

(Picture 23).

1. Put on the harness.

2. Adjust the harness for the best work position.

3. Adjust the side straps until the weight is equally

distributed across your shoulders (Picture 26).

4. Adjust the harness until the cutting attachment is

parallel to the ground.

5. Let the cutting attachment stay lightly on the ground.

And then adjust the harness clamp to balance the

product correctly.

Note:

If you use a grass blade, it must balance

approximately 10 cm (4 inches) above the ground to

keep the grass blade from stones and so on.

191 - 002 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 129R in the language / languages: All languages as an attachment in your email.

The manual is 2,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna 129R Manual

Product: