477487
8
Zoom out
Zoom in
Previous page
1/27
Next page
English--- 8
545196768 Rev. 3 5/15/09
GENERAL SAFETY PRECAUTIONS
W ARNING: Bear in mind that:
Engine exhaust fumes contain car-
bon monoxide, which can cause
carbon monoxide poisoning. For
this reason you should not start or
run the mach ine indoors, or any-
where that is poorly ventilated.
The exhaust fumes from the engine
are hot and may contain sparks
which can start a fire. Never start
the machine indoors or near com-
bustible material!
When
f
itting, tighten the nut in the opposite
direction to the direction of rotation of the
cutting attachment. To remove it, undo the
nut in the same direction as the cutting at-
tachment rotates. ( CAUTION! The nut has
a left--hand thread.) Tighten the nut using
the socket spanner.
IMPORTANT!
Only use cutting attachments with the guards
we recommend! See the section on
“Technical data”.
Refer to the instructions for the cutting attach-
ment to check the correct way to load the
trimmer line and the correct line diameter.
Keep the teeth of the blade correctly sharp-
ened! Follow our recommendations. Also re-
fer to the instructions on the blade packaging.
Maintain the correct blade setting! Follow our
instructions and use the recommended file
gauge.
W ARNING: Theinsideofthe
muffler contain chemicals that may
be carcinogenic. Avoid contact with
these elements in the event of a
damaged muffler.
The nylon lining inside the locking nut must
not be so worn that you can turn it by
hand. The lining should offer a resistance
of at least 1.5 Nm. The nut should be re-
placed after it has been put on approx. 10
times.
Cutting equipment
This section describes how to choose and
maintain your cutting equipment in order to:
S Reduce the risk of blade thrust.
S Obtain maximum cutting performance.
S Extend the life of cutting equipment.
W ARNING: Muffle rs fitted with
catalytic converters get very hot
duringuseandremainsoforsome
time after stopping . This als o applies
at idle speed. Contact can result in
burns to the skin. Remember the risk
of fire!
Regularly check that the muffler is securely
attached to the machine.
Locking nut
A locking nut is used to secure some types
of cutting attachment.
W ARNING: Always stop the en-
gine before doing any work on the
cutting attachment. This continues
to rotate even after the throttle has
been released. Ensure that the
cutting attachment has stopped
completely and disconnect the
lead from the spark plug before
you start to work on it.
W ARNING: Using an incorrect
cutting attachment or an incorrect-
ly sharpened blade increases the
risk of kickback.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 128R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 128R in the language / languages: English, Spanish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 128R

Husqvarna 128R User Manual - German, Dutch, French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info