734099
5
Zoom out
Zoom in
Previous page
1/560
Next page
Make sure that you assemble the cover and shaft
correctly before you start the engine.
Safety instructions for operation
Make sure the product is fully assembled before you
use it.
Before a start, move the product 3 m (10 ft) away
from the position where you filled the fuel tank. Put
the product on a flat surface. Make sure that the
cutting attachment does not touch the ground or
other objects.
The product can cause objects to eject, which can
cause damage to the eyes. Always use an approved
eye protection when you operate the product.
Be careful, a child can come near the product
without your knowledge during operation.
Do not operate the product if there are persons in
the work area. Stop the product if a person goes into
the work area.
Make sure that you are always in control of the
product.
Do not use the product if you cannot receive aid if an
accident occurs. Always make sure others know you
will operate the product before you start to operate
the product.
Do not turn with the product before you make sure
that no persons or animals are in the safety area.
Remove all unwanted materials from the work area
before you start. If the cutting attachment hits an
object, the object can eject and cause injury or
damage. Unwanted material can wind around the
cutting attachment and cause damage.
Do not use the product in bad weather (fog, rain,
strong winds, risk of lightning or other weather
conditions.). Dangerous conditions (such as slippery
surfaces) can occur because of bad weather.
Make sure that you can move freely and work in a
stable position.
Make sure that you cannot fall when you use the
product. Do not tilt when you operate the product.
Always hold the product with your two hands. Hold
the product on the right side of your body.
Operate the product with the cutting attachment
below your waist.
If the choke control is in the choke position when the
engine starts, the cutting attachment starts to turn.
Do not touch the bevel gear after the engine stops.
The bevel gear is hot after the engine stops. Hot
areas can cause injury.
Stop the engine before you move the product.
Do not put down the product with the engine on.
Before you remove the unwanted materials from the
product, stop the engine and wait until the cutting
attachment stops. Let the cutting attachment stop
before you or an aid remove the cut material.
Personal protective equipment
WARNING: Read the warning instructions
that follow before you use the product.
Always use approved personal protective equipment
when you use the product. Personal protective
equipment cannot fully prevent injury but it
decreases the degree of injury if an accident does
occur. Let your dealer help you select the right
equipment.
Use a protective helmet where there is a risk of
falling objects.
Use approved hearing protection that provides
adequate noise reduction. Long-term exposure to
noise can result in permanent hearing impairment.
941 - 004 - 10.04.2019
5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 122LK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 122LK in the language / languages: All languages as an attachment in your email.

The manual is 4,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info