734152

Husqvarna 120 Mark II Manual

21
Zoom out
Zoom in
Previous page
1/448
Next page
depth gauge setting is correct when you no longer
feel resistance as you draw the file along the depth
gauge tool.
To tension the saw chain
Note: Check the tension of a new saw chain frequently
during its running-in period.
1. Loosen the guide bar nuts that hold the clutch cover.
Use the combination wrench. (Fig. 81)
2. Tighten the guide bar nuts by hand as tight as you
can.
3. Lift the top of the guide bar and extend the saw
chain by tightening the chain tensioning screw. Use
the combination wrench. Tighten the saw chain until
it does not hang down from the bottom of the guide
bar. (Fig. 82)
4. Tighten the guide bar nuts using the combination
wrench and lift the tip of the guide bar at the same
time. (Fig. 83)
5. Make sure that you can pull the saw chain round
freely by hand and that it does not sag. (Fig. 84)
To lubricate the cutting equipment
To do a check of the saw chain lubrication
Do a check of the chain saw lubrication each time you
refuel.
1. Start the product and let it run at 3/4 speed. Point the
nose of the guide bar at a light color surface almost
20 cm (8 in) away.
2. After 1 minute of running, a line of oil shows on the
light surface.
3. If you cannot see the line of oil after 1 minute, clean
the oil channel in the guide bar. Clean the groove in
the edge of the guide bar. Make sure the guide bar
nose sprocket turns freely and that there are no
blockages in the lubrication hole. Clean and lubricate
the tip sprocket.
4. Start the product and let it run at 3/4 speed. Point the
nose of the bar at a light color surface almost 20 cm
(8 in) away.
5. After 1 minute of running, a line of oil shows on the
light surface.
6. If you cannot see the line of oil after 1 minute, speak
to your approved dealer.
Transportation
• Put the transportation guard on the cutting
attachment during transportation to prevent injuries.
• Make sure that the product can not move during
transportation.
Storage
• Always put the product away safely when not in
operation. Leakages and fumes from the product can
touch sparks, naked flames from electrical
equipment, electrical mowers, relays/switches,
boilers and more.
• Always save fuel in an approved container.
• Empty the fuel tank and the chain oil tank when the
product is in storage for longer periods of time.
Discard used fluids correctly.
• Put the transportation guard on the cutting
attachment during storage to prevent injuries.
• Remove the spark plug cap from the spark plug and
engage the chain brake before storage.
Technical data
unit
120 Mark II
(P02138HV)
Engine specifications
Cylinder displacement cm
3
38
Spark plug Champion RCJ7Y
658 - 009 - 05.05.2020 21
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 120 Mark II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 120 Mark II in the language / languages: All languages as an attachment in your email.

The manual is 4,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info