Manual Husqvarna 115iHD45 (page 10 of 156) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

733988

Zoom out

Zoom in

1/156

Assembly

Introduction

This section describes how to assemble and adjust the

product.

WARNING: Before you assemble the

product, read the safety chapter and the

assembly instructions.

To connect the battery charger

1. Connect the battery charger to the voltage and

frequency that is specified on the rating plate.

2. Put the plug in a grounded socket outlet. The LED

on the battery charger flashes green one time.

Note: The battery does not charge if the battery

temperature is more than 50 °C/122 °F. If the

temperature is more than 50 °C/122 °F, the battery

charger makes the battery become cool before the

battery charges.

To connect the battery to the product

WARNING: Only use Husqvarna original

batteries in the product.

1. Fully charge the battery.

2. Push the battery into the battery holder of the

product. The battery locks into position when you

hear a click. (Fig. 27)

CAUTION: If the battery does not move

easily into the battery holder, the battery

is not installed correctly. This can cause

damage to the product.

Operation

Introduction

WARNING: Read and understand the safety

chapter before you use the product.

To charge the battery

Note: Charge the battery if it is the first time that you use

it. A new battery is only 30% charged.

1. Connect the battery to the battery charger. (Fig. 28)

2. Make sure that the green charging light on the

battery charger comes on. That means that the

battery is connected correctly to the battery charger.

(Fig. 29)

3. When all LEDs on the battery come on, the battery is

fully charged. (Fig. 30)

4. To disconnect the battery charger from the mains

socket, pull the plug. Do not pull the cable.

5. Disconnect the battery from the battery charger.

Note: Refer to the battery and battery charger manuals

for more information.

To do before you start the product

1. Examine the work area. Remove objects that can be

thrown out.

2. Examine the cutting attachment. Make sure that the

blades are sharp, and have no cracks and damages.

3. Make sure that the product works correctly. Examine

that all nuts and screws are tight.

4. Make sure that the handle and safety devices are

not damaged and are attached correctly. Do not

operate a product with missing parts or is changed

from its initial specification. Use protective gloves

when it is necessary.

5. Make sure that the covers are not damaged and are

attached correctly, before you operate the product.

To start the product

1. Press and hold the start/stop button until the green

LED comes on. (Fig. 31)

2. Press the power trigger lockout on the front handle.

(Fig. 32)

3. To apply full power, press the power trigger. (Fig. 33)

To operate the product

1. Start near the ground and move the product up

along the hedge when you cut the sides. Make sure

that the body of the product does not touch the

hedge. (Fig. 34)

WARNING: Make sure that the front of

the cutting equipment does not touch the

ground.

2. Hold the product near your body for a stable work

position.

3. Be careful and operate the product slowly.

779 - 004 - 15.07.2020

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 115iHD45 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna 115iHD45 Manual

Product: