809496
13
Zoom out
Zoom in
Previous page
1/16
Next page
Standard Range and Solid Door Range C1, C2, & C3Additional model-specific instructions for
CSS1 & FSS2
These instructions should be read in conjunction with the general operating instructions on pp6&7.
Operating Instructions
TO OPERATE THE ELECTRONIC THERMOSTAT
The thermostat has been pre-set, and in most cases it is not necessary to adjust the settings.
When the unit is operating normally, the display will show the current temperature.
To display the set temperature press the button. Press the button again to return to
normal operation.
To set a new temperature, press . The display will flash and the current set temperature
will be displayed. Press the button to increase the set temperature, or press the
button to decrease the set temperature. Press the button to save the new setting. The
display will flash with the new value and then revert to display the cabinet temperature.
Please note:
1. When the chiller is connected to the mains for the first time there will be a short delay
before cooling starts. During this time the Refrigeration Light will flash. After the short
delay, cooling will begin and the Refrigeration Light will be illuminated. When the chiller
reaches the set temperature, the Refrigeration Light will be off.
2. If you do not press any button, after six seconds the controller will return to its normal
display.
DEFROSTING
The unit defrosts automatically at preset intervals. If however the door is opened too often, or
if the unit if in a location with high humidity, or if the contents are changed more frequently, it
may be necessary to defrost the unit manually. To start or stop manual defrosting, press the
button for six seconds. The Defrosting Light will be illuminated. Melt water runs to a
container placed in the compressor compartment and evaporates. After defrosting is complete,
the unit will return to normal operation.
FAST FREEZE (FSS2H ONLY)
To start quick freezing: Press “Up Arrow” for 3 seconds to start the quick-freezing function. The
corresponding LED will light. The compressor will continue to run until the temperature is
reached to the one set.
DOOR OPEN ALARM
If the door remains open for 1min or longer an alarm will be activated. The will show dr and the
room temperature alternately. A buzzer will also sound to indicate the door opening , press any
button to mute the buzzer.
REVERSIBLE DOOR
As standard both CSS1 and FSS2 models are supplied with the door hinged on the right-hand
side, opening from the left hand side. Should you wish to change the opening direction follow
the steps as follows:
1. Unplug the cabinet from the mains.
2. Remove the three screws located at the back of the lid.
3. Pull the lid forward to release.
4. Remove the three screws for the top hinge.
5. Lift the door off the bottom hinge.
6. Move the black stopper on the door over to the right-hand side.
7. Remove the two screws underneath the cabinet to release the Kick Plate.
8. Remove the lower pin to release it and move to the other side.
9. REPEAT Steps 1-7 in reverse to refit door on opposite side.
8 CSS1H-SD-SS-NL-HU / Version 11-2022 Page 9
FSS2H-SD-SS-NL-HU
FSS2H-SD-SS-NL-HU
CSS1H-SD-SS-NL-HU / Version 11-2022 Page
Notes
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husky FSS2H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husky FSS2H in the language / languages: English, Dutch as an attachment in your email.

The manual is 4.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info