Manual Hurom H-300E Series (page 12 of 13) (English)

785966

Zoom out

Zoom in

1/13

English

10. Before

equesting Repair

01. When it starts operating, a

"click" sound is heard.

It is the sound of the motor being assembled with the Multi-screw. This is not a

malfunction.

02. It does not operate only

with the product body.

Check if the chamber set and product body are properly assembled. Make sure to turn

the power off when assembling or disassembling the product.

03. Assemble it so that it is

aligned with the safety sensor.

Check if it is assembled in accordance with the guide mark. Make sure to turn the power

off when assembling or disassembling the product.

04. It does not work.

Check if the power cord is properly inserted. The machine may not work after a long

period of (30 minutes or longer). It will operate normally after the heat of the product

body (motor) cools down.

05. It stops during a normal

operation.

Check if the hopper is properly assembled. If the hopper is assembled incorrectly, the

product will not work. It will operate only when the lock symbol on the chamber and the

hopper's assembly guide mark are assembled in a way that they face each other. Check

if the product is assembled according to the steps specified in the assembly guide. Refer

to the assembly guide page (page 6). Haven't an excessive amount of ingredients or

extremely thick ingredients inserted? Refer to Page 9 of the manual to activate a reverse

rotation.

For safety, a timer, which automatically stops after about 5 minutes from the start of

operation, is set. Press the switch again briefly to start operation.

06. There are crack marks

caused by a Multi-screw or

scratch marks at the top of the

Multi-screw.

In the process of making the molding, curve-shaped marks are created on the sides

and top of the Multi-screw in addition to the straight-lined mold marks. They are normal

parts and do not affect the operation at all.

07. Juice leaks through the

pulp outlet immediately after

the ingredients are inserted.

Depending on the inserted ingredients, small amounts of juice may leak through the

pulp outlet.

This is not a product defect but, rather, a phenomenon caused by the characteristics of

the ingredients. The leakage will stop once the product starts running. If the leakage

continues, contact the Customer Service Center.

08. Juice flows back into the

hopper.

Did you extract juice with the juice cap closed? When juicing with the juice cap closed, the

juice may flow backward into the hopper. If the contents are not sufficiently discharged

even after opening the juice cap again, open the hopper cover and empty out the contents.

09. Juice leaks between the

hopper and the chamber, or

between the chamber and the

product body.

Is the hopper packing or chamber packing assembled correctly? The juice will leak if the

hopper packing or chamber packing has been assembled upside-down or incompletely.

Check if the packing is assembled properly.

10. The hopper does not open.

There may be excessive pulp remaining inside. Operate the produce to discharge the

pulp inside or repeat the process of activating a reverse rotation for about 10 seconds and

then stopping 2 to 3 times. Then, the hopper will open without any issue.

Weren't any foreign substances or solid matters (hard seeds such as persimmon

seeds) inserted? If any foreign substances or solid matters are inserted, parts may be

damaged more seriously when attempting a reverse rotation so contact the Customer

Service Center and request for after-sales service.

11. The chamber shakes

(during juicing).

The product may wobble slightly due to the motions of the product body's motor.

Depending on the ingredients' characteristics (hard or tough), motions are generated

in various magnitudes. This is not a malfunction but, rather, a normal phenomenon

observed when the Multi-screw rotates. Compared to soft ingredients with much water

content, relatively harder ingredients may seem to produce a greater shaking (e.g.,

carrots, potatoes, radishes, beet, kohlrabi, etc.)

12. The discharge cover

is closed but the pulp is

discharged.

Even if the lever is closed, pulp will be discharged naturally. Depending on the

ingredients used, there may be a difference in the amount and speed of discharge.

13. An unusual noise is heard

while juicing.

It is a natural sound produced when ingredients are being crushed. If the ingredients are

hard or tough like apples, carrots, cabbage, celery, beets, etc., the extraction noise may

be louder than that heard when juicing softer ingredients.

14. The Multi-screw stopped

during operation but a reverse

rotation does not work

automatically.

If the power is unstable, the product may not perform a reverse rotation automatically.

Refer to Page 9 of the manual and activate a reverse rotation.

15. During straining, it

automatically ends before the

5-minute timer ends.

It is a function that automatically shuts down to protect the product in case the automatic

reverse rotation is operated often during straining. This may occur if it is impossible to

strain or if uncut ingredients are added. Please refer to Page 5 of the manual for the

instructions on each ingredient and insert the ingredients accordingly.

Check the following before asking for repair. For follow-up service and any inquiry

you may have while using the product, please contact our Customer Center, or

homepage at http://www.globalhurom.com Check the manufacturer’s number or

the number under the barcode when requesting for follow-up service or parts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hurom H-300E Series in the language / languages: English as an attachment in your email.

The manual is 3.66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hurom H-300E Series Manual

Product: