Manual Hunter EC (page 26 of 36) (English)

685887

Zoom out

Zoom in

1/36

RUN TIMES

AUTOMATIC

7. Press the button until you reach the station that you would like

watering to begin.

8. Return dial to AUTOMATIC (program will water the entire program

beginning with the station number last left in the display, then

controller will return to automatic mode with no change in the

previously set program).

NOTE: The station that is on the display when you turn

the dial to AUTOMATIC will be the first station to run.

The controller will then proceed to water in sequential

order only. It will not water previous stations. Example:

If you turn the dial to AUTOMATIC with the display read-

ing station 3, the controller will water stations 3 through

6 in the program, but not return to stations 1 and 2.

PROGRAMMING THE CONTROLLER (continued) ..............................................................

One Touch Manual Start and Advance

You can also activate all stations to water without using the dial.

1. Hold down the button for 2 seconds.

2. This feature automatically defaults to program A. You can select

program B or C by pressing the

program.

3. The station number will be flashing. Press the

button to scroll

through the stations and use the or button to adjust the sta-

tion run times. (If no buttons are pressed for a few seconds dur-

ing step 2 or 3, the controller will automatically begin watering.)

4. Press the button to scroll to the station you wish to begin with.

After a 2 second pause, the program will begin.

This feature is great for a quick cycle when extra watering is needed or

if you would like to scroll through the stations to inspect your system.

HIDDEN FEATURES .................................................................................................................

Programmable Delay Between Stations

This feature allows the user to insert a delay between when

one station turns off and the next station turns on. This is

very helpful on systems with slow closing valves or on

pump systems that are operating near maximum flow or

have slow well recovery.

1. Start with the dial in the AUTOMATIC position.

2. Press and hold the button down

while turning the dial to the SET

STATION RUN TIMES position.

3. Release the

button. At this point the

display will show a delay time for all

stations in seconds, which will be

blinking. The DELAY icon shall also be lit at this time.

4. Press the

and buttons to increase or decrease the

delay time between 0 and 1 minute 40 seconds in

5 second increments.

5. Return the dial to the AUTOMATIC position.

Clearing the Controller's Memory/

Resetting the Controller

If you feel you have misprogrammed the controller, there is a process

that will reset the memory to factory defaults and erase all programs

and data that has been entered into the controller.

1. Press and hold down the

, and buttons.

2. Press and release the reset button in the lower wiring compartment.

3. Release the , and buttons. The display should now show

12:00 am. All the memory has been cleared and the controller may

now be reprogrammed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hunter EC in the language / languages: English as an attachment in your email.

The manual is 0,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hunter EC

Hunter EC User Manual - German - 16 pages

Hunter EC User Manual - Dutch - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hunter EC Manual

Product: