685907
88
Zoom out
Zoom in
Previous page
1/100
Next page
81
wait period has elapsed or the radio carrier signal stops,
with no more tones.
A longer DTMF wait allows slower typing speeds of the
command on the radio. The trade-off is that the longer
wait means that it will take longer for the action to be
carried out (in other words, if the Wait is 5 seconds, it will
be 5 full seconds after the command has been sent before
the sprinkler turns on).
This setting is not shown if there is no radio. This setting
does not affect ICR remote commands.
MR DEFAULT RUN TIME (RADIO ONLY)
Default = 30 Minutes. This sets the automatic run time
for any station or SSG that is started by a Maintenance
Radio command, if no run time has been specified in
the On command. It is possible to turn a station or SSG
on without specifying a run time, and this setting will
automatically turn them off after the specified time if they
are not turned off by an Off comand. The Default Run Time
can be changed in 1 minute increments up to a maximum
of 60 minutes. This setting is not shown if there is no radio
and does not affect ICR remote commands.
MODEM TYPE
Indicates presence of a telephone modem in the Com
module. This display is informational and cannot be
changed from the Com module.
COUNTRY CODE
If a telephone modem is detected, the country code may
need to be changed to work with regional data modem
requirements. The default setting is 0 and for most
countries countries this is the correct selection.
If your country appears on the following list, change the
code display to the number shown:
Country Code
Australia 2
Czech Republic 3
Hong Kong 1
Hungary 1
India 1
Indonesia 1
Israel 1
Japan 4
North Korea 1
Malaysia 1
New Zealand 5
Philippines 1
Poland 1
Singapore 1
Slovenia 1
South Africa 6
Vietnam 1
To change the country code, press Enter and the code will
be highlighted. Use the + or buttons to select the code,
and press Enter. The code will now be set.
HWIM
Indicates presence of a Hardwire Interface Module
(ACC-HWIM) installed in the controller.None indicates
no HWIM has been found, Installed indicates that the
HWIM is installed and has been detected. This display
is informational and cannot be changed from the Com
module.
ENTER DIAGNOSTICS
To use the built-in communications diagnostics, press the
Enter button at this display.
This will allow you to select from the following diagnostic
functions (use the up or down arrow buttons to move
through the choices).
Communications Status display [MOD RAD HW]
Pressing the left arrow button at any time will show a
status display for communications, showing transmit and
receive activity for each communications type. The display
shows: MOD RAD HW #, indicating Modem, Radio,
Hardwire, and number of data packets sent.
Under each item MOD, RAD, and HW, the letter T shows
transmit activity and R shows receiving data for that
communications component. The symbol * shows other
radio traffic (“carrier detect).
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hunter ACC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hunter ACC in the language / languages: English as an attachment in your email.

The manual is 7,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hunter ACC

Hunter ACC User Manual - German - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info