522300

Humminbird PiranhaMax 190C Manual

17
Zoom out
Zoom in
Previous page
1/52
Next page
Preparing the Mounting Location
After determining the mounting location for the
transducer, follow the steps below to position and
mount the transducer bracket.
1. Make sure that the boat is level on the trailer,
both from port to starboard and from bow to
stern, by placing your level on the deck of the
boat, first in one direction, then in the other.
2. Hold the mounting bracket against the transom
of the boat in the location you have selected
(Figure 13). Align the bracket horizontally, using
the level; make sure that the lower screw hole
protrusion does not protrude past the bottom of
the hull, and there is at least 1/4" clearance
between the bottom of the bracket and the
bottom of the transom for fiberglass boats, and
1/8" clearance for aluminum boats (Figure 14).
NOTE: If you have a flat-bottomed aluminum boat, some
additional adjustment may be needed to accommodate
the rivets on thebottom ofthe boat (i.e. the gap may need
to be a little smaller than 1/8"). This will help you to avoid
excessive turbulence at high speeds.
NOTE: If your propeller moves clockwise (in forward, as
you're facing the stern of the boat from behind), mount
the transducer on the starboard side. If your propeller
moves counter-clockwise (in forward, as you're facing the
stern of the boat from behind), mount the transducer on
the port side.
3. Continue to hold the bracket on the transom of
the boat, and use a pencil or marker to mark
where to drill the two mounting holes. Mark the
drill holes near the top of each slot, making sure
that your mark is centered in the slot (Figure 15).
NOTE: The third hole should not be drilled until the
angle and height of the transducer is finalized, which
you will not do until a later procedure.
Level
Level
Figure 13
Using the Mounting Bracket to
Mark the Initial Drill Holes
Mark Initial
Drill Holes
Figure 15
3rd hole
1/8”for aluminum
1
Boat Hull Types Require
Different Mounting Positions
1/8” for aluminum
1/4” for fiberglass
Figure 14
Positioning the Mounting Bracket
11
Transom Transducer Installation
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Humminbird PiranhaMax 190C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Humminbird PiranhaMax 190C in the language / languages: English as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info