522308

Humminbird 325 Manual

64
Zoom out
Zoom in
Previous page
1/68
Next page
57
Grayscale The use of varying shades of gray to represent the strength of the sonar signal
on the display. Traditionally, the strongest sonar signals are represented in black, and
progressively weaker signals are represented in progressively lighter shades of gray.
Noise The unintentional, external sound waves that interfere with the optimal operation
of sonar. Noise appears as random “dots“ on the display and is caused by a variety of
sources. Many Humminbird® products have a Noise Filter menu setting that allows the user
to clear the screen of noise that is difficult to eliminate (also, see Troubleshooting).
Pixels The “picture elements“, or small square blocks, that make up the image on the LCD.
Measured as a vertical by horizontal number (i.e. 640V x 320H), this key specification
typically indicates the quality of resolution. In fishfinders, the total resolution (vertical
multiplied by horizontal) is often less important than the “Vertical Pixel“ resolution because
a greater number of vertical pixels provide finer resolution of targets detected by sonar.
Sonar information on the horizontal axis can vary greatly, depending on boat speed and the
Chart Speed setting.
Power Output The amount of sound energy emitted into the water by the transducer’s
transmitter. Power output is measured using either RMS (Root Mean Square) or P-T-P (Peak-
to-Peak) measurement systems. Either method is acceptable, but it is important when
comparing power outputs, to make sure that the same measurement system is being used
for both outputs, because P-T-P numbers are 8 times higher than RMS numbers. Greater
power output allows the sonar signal to penetrate through weeds and thermoclines, reach
deeper depths and operate more effectively in noisy environments, such as when the boat
is running at high speed.
Pulse Width (Pulse Length) The length of time that a sonar sound burst is transmitted
into the water. Shorter pulse widths provide better target separation, but cannot travel to
great depths. Longer pulse widths provide better depth penetration, but result in poorer
target separation. Humminbird® varies pulse width based on depth to optimize both target
separation and depth performance. See
Target Separation.
Second Return Describes the appearance of a second sonar return below the primary
sonar return (bottom contour) at exactly twice the true depth. The second return is caused
by the same sonar energy bouncing off the bottom once, rebounding to the water surface
and then traveling back down to the bottom to be reflected again. Second returns are more
common in shallow water and over hard bottoms; it is possible to see a third sonar return
under some circumstances. The second return provides useful information to help
determine bottom hardness, as areas with harder bottoms will generally create a second
return. The second return can be used as a guide to set Sensitivity when in shallower water.
Glossary
… 64 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Humminbird 325 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Humminbird 325 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info