669337
9
Zoom out
Zoom in
Previous page
1/27
Next page
07/2011 9
english
5 Operation
Warning!
Before switching the machine on,
make sure that you observe all safety
instructions.
Switching the paper shredder on
Set the sliding switch to "AUTO"
for automatic mode.
The "Power" display lights up.
Note: You can increase the durability of your
shredder by removing staples and small paper-
clips from the paper.
• Feed the paper into the centre
of the paper slot, but never insert
more than 10 sheets at the same
time. When there is a paper jam,
the cutting unit switches to reverse and pushes
the paper out again.
h The light barrier starts the cutting unit auto-
matically. Therefore, with thin paper strips,
make sure the light barrier detects them.
h When the feed opening is clear of paper
again, the cutting device switches off.
Use the designated opening to
shred CDs and credit cards. Feed
the CDs in one by one.
Empty the CD container at the latest after
shredding 6 CDs. To do this, unplug the
power plug and remove the cutting head.
The separate CD container is in the shred-
ded material container.
Note: You cannot use the two cutting units at
the same time. Destroy paper and CDs/credit
cards separately.
Swit ching paper shredder off
Set the sliding switch to "OFF"
Power: Appliance is ready for use
Sliding switch on AUTO or REV
Overload: Machine is overloaded. You have
fed in too much paper.
Set the slider switch to "REV".
h Pa per is pus hed out.
• Se pa ra te pa per stack.
• Set the slider switch to "AUTO"
again.
Feed in pa per successively
Bin Full: Shredded material container full
Notice Empty the cut material container,
immediately because if it is too full, malfunc-
tions can occur in the cutting system.
Pull out the power plug.
Move cutting head away.
Empty cut material container.
Remove cutting head.
Note: The ll level sensor is on
the underside of the cutting head.
Clean the sensor if the "Bin Full"
display remains on even after the
container for shredded material
has been emptied.
Overheat: The motor has overheated.
Let the document shredder cool down for
60 min. You can restart the machine once the
display has gone out.
Cutting unit runs continuously
- The light barrier in the paper feed is blocked
with paper. Press the paper through with a thin
strong piece of cardboard.
- The light barrier is soiled with paper dust.
Clean the sensor with air pressure, a dry paint-
brush or a cloth.
6 LED displays, troubleshooting
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HSM OX 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HSM OX 10 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info