582755
161
Zoom out
Zoom in
Previous page
1/192
Next page
To set up the printer with DSL
1. Obtain a DSL filter from your DSL provider.
2. Using the phone cord supplied in the box with the printer, connect one end to the open port on
the DSL filter, and then connect the other end to the port labeled 1-LINE on the back of the
printer.
NOTE: You might need to connect the supplied phone cord to the adapter provided for your
country/region.
If you do not use the supplied cord to connect from the DSL filter to the printer, you might not be
able to fax successfully. This special phone cord is different from the phone cords you might
already have in your home or office.
As only one phone cord is supplied, you might need to obtain additional phone cords for this
setup.
3. Connect an additional phone cord from the DSL filter to the telephone wall jack.
4. Run a fax test.
If you encounter problems setting up the printer with optional equipment, contact your local service
provider or vendor for further assistance.
Case C: Set up the printer with a PBX phone system or an ISDN line
If you are using either a PBX phone system or an ISDN converter/terminal adapter, make sure you do
the following:
If you are using either a PBX or an ISDN converter/terminal adaptor, connect the printer to the
port that is designated for fax and phone use. Also, make sure that the terminal adapter is set to
the correct switch type for your country/region, if possible.
NOTE: Some ISDN systems allow you to configure the ports for specific phone equipment. For
example, you might have assigned one port for telephone and Group 3 fax and another port for
multiple purposes. If you have problems when connected to the fax/phone port of your ISDN
converter, try using the port designated for multiple purposes; it might be labeled "multi-combi"
or something similar.
If you are using a PBX phone system, set the call waiting tone to "off."
NOTE: Many digital PBX systems include a call-waiting tone that is set to "on" by default. The
call waiting tone interferes with any fax transmission, and you cannot send or receive faxes with
the printer. Refer to the documentation that came with your PBX phone system for instructions
on how to turn off the call-waiting tone.
If you are using a PBX phone system, dial the number for an outside line before dialing the fax
number.
Make sure you use the supplied cord to connect from the telephone wall jack to the printer. If
you do not, you might not be able to fax successfully. This special phone cord is different from
the phone cords you might already have in your home or office. If the supplied phone cord is too
short, you can purchase a longer 2-wire phone cord from your local electronics store and extend
it.
You might need to connect the supplied phone cord to the adapter provided for your country/
region.
If you encounter problems setting up the printer with optional equipment, contact your local service
provider or vendor for further assistance.
148 Appendix B Additional fax setup ENWW
161


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP Officejet 6800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP Officejet 6800 in the language / languages: English as an attachment in your email.

The manual is 8,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of HP Officejet 6800

HP Officejet 6800 Quick start guide - English - 32 pages

HP Officejet 6800 User Manual - German - 209 pages

HP Officejet 6800 User Manual - Dutch - 201 pages

HP Officejet 6800 Quick start guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info