20200
135
Zoom out
Zoom in
Previous page
1/304
Next page
If the job will not print, and a message
appears on the printer control panel display,
see
Interpreting control-panel messages.
Using the computer, check to see if the
printer has been paused. Press S
TOP
to
continue.
If the printer is on a network, check that you
are printing to the correct printer. To verify
that it is not a network problem, connect the
computer directly to the printer with a
parallel or USB cable, change the port to
LPT1, and try to print.
Check the interface cable connections.
Disconnect and reconnect the cable at the
computer and the printer.
Test the cable by trying it on another
computer.
If you are using a parallel connection, make
sure that the cable is IEEE-1284 compliant.
If the printer is on a network, print a
configuration page. (See
Configuration
page.) If an HP Jetdirect print server is
installed, a Jetdirect page also prints. Check
the Jetdirect configuration page to verify that
the network protocol status and settings are
correct for the printer.
To verify that it is not a computer problem,
print from another computer (if possible).
Make sure that the print job is being sent to
the correct port (LPT1 or network printer
port, for example).
Check that you are using the proper printer
driver. (See
Using the printer driver.)
Reinstall the printer driver. (See the getting
started [start] guide.)
Check that the computer port is configured
and working properly. (Try connecting
another printer to that port and printing.)
If printing with the PS driver, on the Printing
submenu (on the Configure Device menu) at
the printer control panel, set PRINT PS
ERRORS=ON, and then print the job again.
If an error page prints, see the instructions
in the next column.
On the System Setup submenu (on the
Configure Device menu) at the printer
control panel, make sure that
PERSONALITY=AUTO.
You might be missing a printer message
that could help you solve the problem. On
the System Setup submenu (on the
Configure Device menu) at the printer
control panel, temporarily turn the Clearable
Warnings and Auto Continue settings off.
Then, print the job again.
The printer might have received a
nonstandard PS code. On the System Setup
submenu (on the Configure Device menu) at
the printer control panel, set
PERSONALITY=PS for this print job only.
After the job has printed, return the setting
to AUTO.
Make sure that the print job is a PS job, and
that you are using the PS driver.
The printer might have received PS code
although it is set to PCL. On the System
Setup submenu (on the Configure Device
menu), set PERSONALITY=AUTO.
ENWW Troubleshooting flowchart 123
135


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP LASERJET4350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP LASERJET4350 in the language / languages: English as an attachment in your email.

The manual is 3,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info