NOTE: To use Wi-Fi Direct, make sure it is enabled. To check Wi-Fi Direct name and password (pin), print a conguration report by pressing and holding the
Resume/Cancel
button until the Ready LED starts blinking, and then release the button.
Troubleshooting
User guide
The user guide includes printer usage and troubleshooting information. Go to www.hp.com/support/ljM14.
Wireless connection setup troubleshooting
NOTE: Only 2.4 GHz band is supported.
Verify that the printer is within the range of the wireless network. For most networks, the printer must be within 30 m (100 ft) of the wireless access
point (wireless router). A USB cable might be required for temporary connection between the printer and the computer. To ensure that the wireless setup
information synchronizes correctly, do not connect the USB cable until prompted to do so.
If your router supports Wi-Fi Protected Setup (WPS) mode, try to connect through this mode:
1. Press the WPS
button on your router.
2. Within two minutes, press and hold the Wireless
button on the printer control panel for at least three seconds, and then release the button.
TheWireless
LED and the Ready LED start blinking together.
3. Wait while the printer automatically establishes the network connection. It takes up to two minutes. When the network connection is established,
theWireless
LED stops blinking and remains on.
4. Continue to install the software.
Check the Wireless LED status from the printer control panel:
1. If the Wireless
LED is o, it means that the wireless connection is not established.
a. Press the Wireless
button on the printer control panel.
b. After the Wireless
LED starts blinking, continue to install the software. When the network connection is established, the Wireless LED stops
blinking and remains on.
2. If the Wireless
LED is on, it means that the wireless connection is established.
a. Check the network name (SSID) info on the Conguration Report/Network Summary: Press and hold the Resume/Cancel
button until the Power/
Ready
LED starts blinking. After you release the Resume/Cancel button, the Conguration Report/Network Summary prints.
b. Make sure the computer is connected to the same wireless network to which you are connecting the printer.
c. Continue to install the software.
3. If the Wireless
LED is blinking, it means that the wireless connection is not established.
a. Restart the printer and the router.
b. Manually connect the printer to your wireless network. Use Wi-Fi Protected Setup (WPS) to connect the printer if the router supports WPS,
orcontinue tothe next step.
c. Uninstall and reinstall the HP software.
Wireless printing
For more information on wireless
printingandwireless setup, go to
www.hp.com/go/wirelessprinting.
Follow these steps to restore the network settings:
1. Remove the USB cable from the printer.
2. Press and hold the Wireless
button on the printer control panel for 20 seconds.
3. When the Attention
LED and the Power LED start blinking together, release the Wireless button. The printer restarts automatically.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for HP LaserJet Pro M17 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of HP LaserJet Pro M17 in the language / languages: All languages as an attachment in your email.
The manual is 19,22 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
