655054
10
Zoom out
Zoom in
Previous page
1/30
Next page
If the system does not boot, press and hold any key. If the system beeps, then the keyboard is operating
correctly.
Check all cable connections for loose connections or incorrect connections.
Wake the computer by pressing any key on the keyboard or pressing the power button. If the system
remains in sleep mode, shut down the computer by pressing and holding the power button for at least
four seconds. Then press the power button again to restart the computer. If the system will not shut
down, unplug the power cord, wait a few seconds, and then plug it in again. The computer will restart if
automatic start on power loss is set in Computer Setup. If the computer does not restart, press the
power button.
Recongure your computer after installing a non-Plug and Play expansion board or other option.
Be sure that all the needed device drivers have been installed. For example, if you are using a printer,
you need a driver for that printer model.
Remove any bootable media (CD/DVD or USB device) from the system before turning it on.
If you have installed an operating system other than the factory-installed operating system, check to be
sure that it is supported on the system.
CAUTION: When the computer is plugged into an AC power source, there is always voltage applied to the
system board. To reduce the risk of system board or component damage, always disconnect the power cord
from the power source before opening the computer.
Blink or beep codes: Interpreting POST diagnostic rear panel LEDs and audible codes
If you see ashing LEDs on the rear of the computer or if you hear beeps, see the Maintenance and Service
Guide (English only) for interpretation and recommended action.
HP Support Assistant
HP Support Assistant is an HP application that helps you maintain the performance of your computer and
resolve problems through automated updates and tune-ups, built-in diagnostics, and guided assistance. HP
Support Assistant is preinstalled on all HP or Compaq computers with Windows 7.
To access HP Support Assistant in Windows 7, double-click the HP Support Assistant icon on your desktop.
Using HP PC Hardware Diagnostics
HP PC Hardware Diagnostics is a Unied Extensible Firmware Interface (UEFI) that allows you to run diagnostic
tests to determine whether the computer hardware is functioning properly. The tool runs outside the
operating system so that it can isolate hardware failures from issues that are caused by the operating system
or other software components.
When HP PC Hardware Diagnostics (UEFI) detects a failure that requires hardware replacement, a 24-digit
Failure ID code is generated. This ID code can then be provided to support to help determine how to correct
the problem.
NOTE: To start diagnostics on a convertible computer, your computer must be in notebook mode and you
must use the keyboard attached.
To start HP PC Hardware Diagnostics (UEFI), follow these steps:
1. Turn on or restart the computer, and quickly press esc.
2. Press f2.
The BIOS searches three places for the diagnostic tools, in the following order:
4 Chapter 1 Getting Started in Windows 7
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP Elite Slice at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP Elite Slice in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of HP Elite Slice

HP Elite Slice User Manual - English - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info