Manual Hozelock 2597 (page 6 of 60) (All languages)

661708

Zoom out

Zoom in

1/60

H) (Fig.3f).

INSTALLING THE REEL

• Release the locking clasp on the reel. (Fig.2a).

• Mount the reel onto the bracket by tipping the reel

backwards and placing the top bracket socket of the

reel onto the bracket (Fig.4a).

• Allow the Auto Reel to fall onto the bottom bracket

(Fig.4b).

• Lock in place using the locking clasp (Fig.4c).

Ensure that the clips are snapped into place.

• Attach the threaded tap connector (Contents D) to

your tap and connect the feeder hose to it via the

hose end connector (Fig.5).

• Test the assembly to ensure the reel swings freely

through 180°. Turn the tap on and run the water

through the reel before using it for the first time.

Check for leaks and re-tighten hose connections if

necessary.

• A padlock (not supplied) may be fitted to the reel

when left unattended on the wall (fig.6a).

• There is an accessory park point at the bottom of the

bracket for stowage of hose end accessories (fig.6b).

USING THE REEL

• To pull out the hose, take hold of the hose end and

walk away from the reel in any direction.

• The reel has an automatic latch to hold the hose in

place for use at any required length. The hose may

be placed on the ground and will not rewind.

• If more hose is required, pull out as necessary.

• To rewind the hose gently pull the hose between

15 to 30cm away from the reel to release the locking

mechanism. Walk back towards the reel. Always hold

the hose end whilst it rewinds. If you are struggling

to do this try;

Turn off the tap and let the water out of the hose by

opening the hose nozzle/gun.

Walk back to the reel with the end of the hose and

trigger the rewind mechanism by taking hold of the

hose near to the reel, and gently pull the hose about

15 to 30cm to release the latch.

(Ensure that nothing is obstructing the hose whilst

the rewind procedure is active.)

IMPORTANT: THE HOSE END MUST BE WALKED

BACK TO THE REEL.

USING THE SAFETY LOCK

Fig 7.

• Operate the safety lock by using the dial on the side

of the reel.

• The safety lock has two functions:

To stop the hose being pulled out when fully

re-wound

To stop accidental rewind while the hose is in use.

• To lock, turn the dial towards the (padlock closed)

symbol (Fig.7a). To unlock, turn the dial so that it

points towards the (padlock open) symbol (Fig.7b).

• For added security always lock the reel when

unattended.

Warning

Do not operate the safety lock while the reel is

turning.

IMPORTANT:

To prevent damage or injury:

DO NOT:

Let go of the hose while rewinding.

Always walk back to the reel holding the hose.

Place fingers or objects in the hose aperture of the

reel during operation.

Attempt to remove the screws from any part of

the product.

Remove the grey ball from the watering hose.

DO:

Remove the reel from the wall in winter to prevent

frost damage.

Keep the floor/ground below the reel as clear as

possible from water to minimise any risk of

slipping.

Turn the tap off when not in use.

To prevent damage being caused to your Auto

Reel over the winter months it is advisable that

the excess water be dispelled from the hosepipe.

This can be done by completing the following steps:

1. Disconnect the feeder hose from the tap

2. Place the end of the feeder hose on the ground

3. Pull out all of the hose ensuring the hose end

connection is ‘closed’ and then completely

retract it

4. Excess water will dispel from the feeder hose

5. Repeat step 3 several times

By dispelling the excess water from your Auto Reel,

it will not only become lighter to transport inside

during winter, but will reduce the risk of water

freezing inside the reel.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hozelock 2597 in the language / languages: All languages as an attachment in your email.

The manual is 2,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hozelock 2597 Manual

Product: