661705

Hozelock 2490 Manual

5
Zoom out
Zoom in
Previous page
1/42
Next page
5
(Fig.1)
A. 93273 - Auto Reel
B. 83360 - Wall Bracket
C. 93411 - Feeder Hose
D. 2175 - Threaded tap connector
E. 2166 - Hose End Connector
F. 2185 - Waterstop Connector
G. 53025 x4 - Wall Plug
H. 53112 x4 - Screws
I. 2292 - Hose Nozzle
J. 83304 - Side Disc
TOOLS NEEDED:
• Flat-ended screwdriver
• Philips screwdriver
• Tape measure
• Ø7mm masonry drill bit
• Electric drill
• Spirit Level
FIT THE WATER INLET HOSE
Fig 1.
A. One side of the reel has its side disc already removed.
Lay the reel on a soft surface with this side uppermost.
B. Two screws hold in place the plate on the internal hose
connector. Unscrew them.
C. Pass the 2 metre water inlet hose through the opening
from the outside to the inside of the casing. Unscrew
the large hose nut connector and put it on the hose.
Push the hose under the teeth of the small clasp.
Tighten the hose nut. Screw the internal hose
connector back in place.
D. Fit the side disc. Attach the 2166 hose end connector
to the free end of the water inlet hose. Attach the
2185 water stop connector to the watering hose.
If the water inlet hose supplied is too short to reach
your tap, replace it with a good quality 13mm (1/2”)
hose.
SELECT A SUITABLE POSITION FOR
INSTALLATION
Fig. 2
The reel is designed for external use only and is not
suitable for use with indoor taps.
The reel should be able to swivel through 180º. Allow
50cm of clearance on both sides of the wall bracket.
If the hose is to be used around corners, mount the reel
at least 1m from the corner and use a hose guide, part
no. 2392, which is not supplied.
FIX THE WALL BRACKET
Fig 3.
Important: Ensure that the bracket is vertical.
Use the four plugs and screws supplied. The plugs and
screws supplied are designed for use on standard brick
and concrete or timber walls only. To fix the bracket to
any other surface, you should use screws and plugs
appropriate for that surface.
INSTALLING THE REEL
Fig 4.
1. Align the back of the reel with the wall bracket.
2. Slide the pivot tube through the reel and wall bracket
from the top.
3. Attach the threaded tap connector to your tap and
connect the water inlet hose to it.
4. Attach the 2292 nozzle onto the end of the watering
hose.
Test the assembly to ensure the reel rotates freely
through 180º. Turn the tap on and run the water
through the reel before using it for the first time. Check
for leaks and re-tighten assembled parts if leaks
appear.
A padlock (not supplied) may be fitted to secure the
reel when left unattended on the wall (fig 4A).
Fig 4B.
There is a park point on the top of the pivot tube for
stowage of the water inlet hose end when not in use.
There is an accessory park at the bottom of the bracket
for stowage of hose end accessories.
USING THE SAFETY LOCK
Fig 5.
Operate the safety lock by using the lever on the side of
the reel.
The safety lock has two functions:
1. To stop the hose being pulled out when fully re-wound.
2. To stop accidental rewind while the hose is in use.
To engage the safety lock, turn the lever towards the
symbol. To disengage it, turn the lever so that it
points towards the symbol.
For added security always engage the safety lock when
the reel is unattended.
Do not operate the safety lock while the reel is turning.
USING THE REEL SAFELY
1. To unwind the hose, disengage the safety lock, (see
above) take hold of the hose end and walk away from
the reel in any direction.
2. The reel has an automatic latch to hold the hose in
place at the required length. You will hear 4 latch
‘clicks’ every metre as the hose is unwound.
When the hose is at the required length, stop and
slowly pull the hose until you hear one of the 4 latch
clicks. The hose is now held in place for use, or may be
placed on the ground without rewinding. At this point,
you can engage the safety lock if required.
3. If you need more hose, disengage the safety lock if
necessary, take hold of the hose end and walk away
from the reel with the hose repeating the automatic
latching procedure.
4. The automatic latch is released by pulling the hose
away from the reel past the 4 latch clicks. THE HOSE
GB
Contents
Assembly and installation of
the Auto Reel
Warning
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hozelock 2490 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hozelock 2490 in the language / languages: All languages as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info