669343
18
Zoom out
Zoom in
Previous page
1/46
Next page
14
UK
Installation
The device should be installed in accordance with the drawing on the rst page of the
user manual. Any other installation position may result in serious damage to the device.
Installation should take place as close as possible to a cold water connection. The product
should be protected from the effects of frost (for example in caravans, summer houses,
etc.).
When mounting swivels and compression ttings, always use 2 open-end spanners in or-
der to prevent bending and twisting pipes and accessories.
Frost
In case of risk of frost in a room, the device should not be installed in this room. If, de-
spite this advice, the device is installed in a room where there is a risk of frost, the device
should be emptied before the risk arises.
The Hotto is not suitable for installation on a reverse osmosis installation or a
water softening installation with pH reduction.
Always use the Hotto safety group for connecting. Never use the device without a safety
group!
Use of a different tap than the supplied Hotto 3-in-1 tap, or a change in the
tap/boiler combination, may damage the product. The warranty will always become invalid
in case of incorrect installation or modication!
Important: Never insert the plug in the earthed wall socket before the appliance is lled
with water!
Never connect the Hotto boiler to a hot water pipe. This might decrease the life
expectancy of the boiler due to increased limescale build-up on the heating element
and inside the mixing valve.
Water quality
In areas where the water hardness is above 12 °dH a water lter approved by Hotto
must be placed in the supply water line. Failure in doing so will void the warranty. See
www.hotto.com for more information and ordering options for water lters. The water
quality must meet the following requirements:
pH scale 7 - 9.5 pH
Fe (Iron level) < 0.2 mg/l
CI (Chlorine content) < 150 mg/l
DH (German Hardness) < 12 °DH
Minimum ow pressure 0.1 MPa
2A Connecting the tap
Step 1: Connect the cold and hot water hoses (G) by screwing them in the tap.
Step 2: Place the tap in the hole (ø 33 - 40 mm). The Hotto logo of the rosette (A) with
rubber ring (B) should be pointing towards the front.
UK
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotto Arco at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotto Arco in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hotto Arco

Hotto Arco Additional guide - English - 2 pages

Hotto Arco Additional guide - English - 3 pages

Hotto Arco Installation Guide - English, German - 2 pages

Hotto Arco Additional guide - Dutch - 2 pages

Hotto Arco Additional guide - Dutch - 3 pages

Hotto Arco Installation Guide - Dutch - 2 pages

Hotto Arco Additional guide - French - 2 pages

Hotto Arco Additional guide - French - 3 pages

Hotto Arco Installation Guide - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info