Manual Hotpoint TCD 93B 6H (page 11 of 88) (English, French, Portuguese, Spanish)

512833

Zoom out

Zoom in

1/88

Start and Programmes

88:88

! Warning, after pressing the Start/Pause button , the

programme cannot be changed.

To change a selected programme, press the Start/Pause

button , the light flashes Amber to indicate the

programme is paused. Select the new programme and

any options required, the light will then flash green.

Press the Start/Pause button again and the new

programme will start.

●

Option buttons

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected, by pressing a programme selection

button, before an option can be selected. Not all options

are available for all programmes (see Programmes Table).

If an option is not available and you press the button, the

buzzer will beep 3 times. If the option is available the

indicator, on the display unit above the bottom buttons,

lights to show that the option has been selected.

Time Delay (Delay Timer)

The start of some programmes (see The Display and

Programmes tables) can be delayed for up to 24 hours.

Ensure the water container is emptied before setting a

delayed start.

Crease Care

The pre-care option is only available if a delayed start has

been selected. It tumbles the clothes occasionally during the

delayed period to help prevent creases developing.

The post-care option occasionally tumbles the clothes after

end of the drying and cool tumble cycles to prevent creases

developing, should you not be available to remove the load

immediately the programme is complete. Note: The

Start/Pause light flashes Amber during this phase.

Selecting this option enables both the pre and post care

functions if appropriate.

Note: If you have selected the Sound option this option is

not available.

Heat Level button, Display and Icons

Not all programmes allow you to change the heat level

and some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the display briefly shows

the selected heat level, along with a display of the selected

level icon:

HIGH HEAT MEDIUM HEAT LOW HEAT

Sound

Available on all programmes and allows the buzzer to

give a signal at the end of the drying cycle, to remind

you that the clothes are ready to be removed.

Note: If you have selected the Crease Care option this

option is not available.

Extra Care

This Anti-Ageing function for Cottons helps to maintain the

brightness of your laundry for a long time, thanks to the

correct drum rotation (reduced in the last part of the cycle)

and the correct temperature.

Note: It cannot be used with the ‘Extra Dry’, ‘Cupboard Dry’

and ‘Light Dry’ dryness levels.

The Controls

Quick Dry

This option is for small loads up to 1kg.

Note: can only be used with the ‘Cupboard Dry’ setting.

Your drying time is very much reduced with a huge

time saving up to 53% on cottons and 50% on

synthetics.

●

TIME DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for a

drying programme (see The Display).

The display also shows if there is a problem with your

dryer, if this occurs the display will show F followed by

a fault code number (see Troubleshooting).

●

Empty Water Container

(If you have plumbed your dryer to a drain this icon can be

ignored, as there is no need to empty the water container).

Messages are displayed to reminds you to empty the

water container (see The Display).

If the water container fills during a programme, the heater

turns off and the dryer does a period of Cool Tumble.

After this it stops and a message tells you to

EMPTY WATER BOTTLE .

You must empty the water container and restart the dryer

or the clothes will not dry. After re-starting the dryer the

message will take a few seconds to go out.

To avoid this always empty the water container each time

you use the dryer (see Maintenance).

●

Door Opening

Opening the door during a programme will stop the dryer

and have the following effects:

Note: The Start/Pause light flashes Amber during the Post

Care phase of a programme.

●

The display shows PAUSE .

●

During a delay phase the delay will continue to count

down. The Start/Pause button must be pressed to

resume the delay programme.

The display will change to show current status.

●

During the drying part of the programme, the colons

on the display stop flashing to show that the time has

stopped counting down.

The Start/Pause button must be pressed to resume

the programme. The display will change to show the

current status, the colons flash and count down

continues.

●

During the Post Care phase, the programme ends.

Pressing the Start/Pause button will restart a new

programme from the beginning.

●

Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, press and hold the

On/Off button until the display briefly shows

POWER ON

and the dryer reactivates. Then press the Start/Pause

button and the programme will resume.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint TCD 93B 6H in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint TCD 93B 6H Manual

Product: