Manual Hotpoint SIAL 11010 Aquarius (page 4 of 16) (English)

670831

Zoom out

Zoom in

1/16

Installation

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto its

back.

Positioning and levelling

1. Position the dishwasher on a level sturdy floor. If the floor is

uneven, the front feet of the appliance may be adjusted until it

reaches a horizontal position. If the appliance is levelled correctly,

it will be more stable and much less likely to move or cause

vibrations and noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive

transparent strip* under the wooden shelf in order to protect it

from any condensation which may form.

3. Place the dishwasher so that its sides or back panel are in

contact with the adjacent cabinets or the wall. This appliance can

also be recessed under a single worktop*

(see the Assembly

instruction sheet)

4*. To adjust the height of the rear foot, turn the red hexagonal

bushing on the lower central part at the front of the dishwasher

using a hexagonal spanner with an opening of 8 mm. Turn the

spanner in a clockwise direction to increase the height and in an

anticlockwise direction to decrease it.

(see Building-in instruction

sheet attached to the documentation)

The dishwasher meets the requirements set out by the regulations

in force concerning safety and electrical equipment.

Any technical checks should be conducted exclusively by a

trained and authorised technician: Repairs carried out by

unaithorised persons will invalidate the guarantee, as well as

posing a potential hazard to the user.

The manufacturer declines all responsibility for damage to

persons or property resulting from failure to observe the above

precautions, from tampering with even a single component or

from the use of non-original spare parts.

Connecting the water supply

Adaptation of the water supply for installation should only be

performed by a qualified technician.

The water inlet and outlet hoses may be positioned towards the

right or the left in order to achieve the best possible installation.

Make sure the dishwasher does not bend or squash the hoses.

Connecting the water inlet hose

• To a 3/4” gas cold or hot water connection point (max. 60°C).

• Run the water until it is perfectly clear.

• Screw the inlet hose tightly into position and turn off the tap.

If the inlet hose is not long enough, contact a specialist store

or an authorised technician

(see After Sales Service)

The water pressure must be within the values indicated in

the Technical Data table - otherwise the dishwasher may be

function properly.

Make sure the hose is not bent, compressed or kinked.

DO NOT overtighten the hose connector, hand tight is

sufficient.

Tap connections*: A range of adaptors are available to suit

your tap.

Connecting the drain hose

Connect the drain hose (without bending) to a drain duct with a

minimum diameter of 2 cm. (A)

The drain hose connection must be at a height ranging from 40

to 80 cm (from 15’’ to 31’’) from the floor or surface where the

dishwasher rests.

• before connecting the drain hose, remove any internal

restrictions; this will prevent a build up of debris which could

cause a blockage.

• remove any restrictions from the waste spigot and ensure that

the sealing bung is removed (B).

It MUST NOT be connected to a surface water drain.

Ensure the drain hose is securely

attached, to prevent it coming away

while the machine is in use and

causing a flood.

Fit hose to waste securely using

a “Jubilee” type clip.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water supply

in the event of anomalies or leaks from inside the appliance.

Some models are also equipped with the supplementary safety

device New Acqua Stop*, which guarantees anti-flooding

protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstances should the water inlet hose be cut as it

contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make sure that:

• The socket is earthed and complies with current regulations;

• the socket can withstand the maximum load of the appliance

as shown on the data plate located on the inside of the door

(see chapter Description of the appliance);

• The power supply voltage falls within the values indicated on

the data plate on the inside of the door.

• The socket is compatible with the plug of the appliance. If this

is not the case, ask an authorised technician to replace the

MIN 40 cm

MAX 80 cm

* Only available in selected models.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint SIAL 11010 Aquarius in the language / languages: English as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint SIAL 11010 Aquarius Manual

Product: