665369

Hotpoint SGDC11AA1 Manual

13
Zoom out
Zoom in
Previous page
1/16
Next page
1313
en
• The plug was not inserted or is not making contact.
• Make sure the temperature is not set to Min.
• The temperature indicator light is on. This shows that the iron is
warming up. The indicator light will turn off when the set temperature
is reached.
• Not enough water in the water reservoir. Fill up the water reservoir.
• The iron is not hot enough. Place the iron on the special supporting
base and wait until the temperature indicator light turns off before you
start ironing.
• The plate temperature may be too low because the steam button
has been activated too frequently. Slightly increase the time interval
between steam shots.
• Make sure the steam control is not set to Min.
• There may be residues in the vaporisation chamber. Clean it as
shown in the chapter “Cleaning and maintenance” under paragraph
“Descaling”.
• You are using perfume, vinegar, starch, scale-removing agents,
ironing products or other chemicals. Remember that these substances
may damage the product. Rinse the water reservoir.
• You are not using the correct water type. Rinse the water reservoir
and add tap water only. In case of very hard water, we recommend
mixing it proportionally with demineralised water - see chapter "Filling
the water reservoir".
• You are using starch. You can use starch directly on the reverse side
of the fabrics and in any case never in the water reservoir.
• The garment was not washed correctly or it has some soap residues.
• Youareironinganewgarmentnotyetwashedforthersttime.
• The plate temperature may be too low because the steam button
has been activated too frequently. Slightly increase the time interval
between steam shots.
• The soleplate temperature is set to a temperature that is too low.
• You used the shot-of-steam function and/or the steam function at a
temperature that was too low. We recommend using these functions
attemperatureshigherthan●●●.
• You are using a temperature that is too high.
• Clean the soleplate - see chapter “Cleaning and maintenance” under
paragraph “Cleaning”.
• You are using starch. You can use starch directly on the reverse side
of the fabrics and in any case never in the water reservoir.
• The garment was not washed correctly or has some soap residues.
• Youareironinganewgarmentnotyetwashedforthersttime.
The soleplate stays cold and
does not warm up.
The temperature indicator
light goes on and off.
Steam comes out in a re-
duced quantity or does not
come out at all.
Impurities coming out of the
soleplate stain the garments.
Water is dripping out of the
soleplate.
The soleplate is dirty or dark
and may stain the fabrics.
TROUBLESHOOTING
Problem Possible causes / Solutions
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint SGDC11AA1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint SGDC11AA1 in the language / languages: English as an attachment in your email.

The manual is 9,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info