670829

Hotpoint FDFEX 11011 EXTRA Manual

6
Zoom out
Zoom in
Previous page
1/20
Next page
6
GB
Technical data
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 13 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply voltage See appliance data plate
Total absorbed power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/EU Waste Electrical
and Electronic Equipment
(WEEE)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Connecting the water supplies
Connectiontothewaterandelectricitysuppliesshould
only be performed by a qualified technician.
The dishwasher should not stand on top of the water
hoses or the electricity supply cable.
Connecting the water inlet hose
The water inlet and outlet hoses and the electricity supply
cable may be positioned towards the right or the left in order
to achieve the best possible installation.
• Toasuitablecoldwaterconnectionpoint:beforeattaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
• Toasuitablehotwaterconnectionpoint:yourdishwasher
may be provided with hot water from the mains supply (if
you have a central heating system with radiators) provided
thatitdoesnotexceedatemperatureof60°C.
Screw the hose to the tap as described for connection to
a cold water supply.
If the inlet hose is not long enough, contact a specialist
store or an authorised technician
(see Assistance)
.
The water pressure must be within the values indicated
in the Technical data table
(see Installation).
The hose should not be bent or compressed.
The appliance must be connected to the water supply
network using new hoses.
Donotuseoldhoses.
Ensure that the new hose supplied is connected and the old
hose is disposed of safely.
DONOTovertightenthehoseconnector,handtightis
sufficient.
Ensure the fill hose is not kinked.
Tap connections*: A range of adaptors are available to
suit your tap.
DO NOT connect the dishwasher to a single outlet
instantaneous water heater or an electric heater.
Sink Waste System
Connecttheoutlethose(withoutbendingit)toadrainduct
withaminimumdiameterof32mm.
Theoutlethosemustbeataheightrangingfrom40to80cm
(from15’’to31’’)fromthefloor/surfacewherethedishwasher
rests (A).
• beforeconnectingthe drain hose, remove any internal
restrictions; this will prevent a build up of debris which
could cause a blockage
• removeanyrestrictionsfromthewastespigotandensure
that the sealing bung is removed (B).
ItMUSTNOTbeconnectedtoasurfacewaterdrain.
•UntietheendoftheGREYdrainagehosefromtherear
of the appliance.
• If fitting an under sink waste disposal unit, cut out the
membrane, bung or blanking plug.
* Onlyavailableinselectedmodels.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint FDFEX 11011 EXTRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint FDFEX 11011 EXTRA in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info