513524

Hotpoint CP9VP6 DE HA Manual

17
Zoom out
Zoom in
Previous page
1/48
Next page
GB
17
THE EQUIPMENT MUST BE EARTHED CORRECTLY.
The hob is designed for operation with an alternating
current at the power supply voltage and frequency
indicated on the data plate (this is located underneath
the hob; alternatively the information may be found at
the end of the instruction manual). Make sure that the
local power supply voltage value is the same as the
value indicated on the data plate. The appliance does
not come with a power supply cable, because the size
of this cable should be determined according to the
type of electrical connection used (see connection
diagram below). Use a H05RR-F-type rubber cable.
Open the terminal board, following the instructions for
the adjacent figure:
To install the power supply cable, follow the instructions
below:
Loosen the cable clamp screw V and the wire
contact screws (fig. 11).
Fix the wires under the screw heads in accordance
with the following diagram.
2
1
1
2
3
4
5
V
Fig.11
Secure the power supply cable by fastening the cable
clamp screw, then put the cover back on.
Electrical
connection
Power supply
voltage
Fuse
Cross-
section
230V -1+N ~ 50Hz 32* A 4 mm²
400V 2+N ~ 50Hz 32 A 4 mm²
400V -3+N ~ 50Hz 25 A 2.5 mm²
230V -2 ~ 50Hz 32* A 4 mm²
230V -3 ~ 50Hz 25 A 2.5 mm²
230V -2+2N ~
50Hz
25* A 2.5 mm²
*Application of the simultaneity coefficient in
compliance with the relevant standard.
Electrical connection
Connecting the power supply cable to the mains
Find a plug which is suitable for the load indicated on
the data plate and fit it onto the cable. The appliance
must be directly connected to the mains using an
omnipolar switch with a minimum contact opening of 3
mm installed between the appliance and the mains.
The switch must be suitable for the load indicated and
must comply with current electrical regulations (the
earth wire must not be interrupted by the switch). The
supply cable must not be placed in areas where any
part of it could reach temperatures higher than 50°C.
Before connecting the appliance to the power supply,
make sure that:
The modulating valve and the electricity supply can
withstand the maximum power of the appliance (see
the data plate for details);
The electricity supply system is earthed correctly, in
compliance with current laws and regulations;
The power socket or omnipolar switch may be reached
easily once the hob has been installed.
TECHNICAL FEATURES:
Voltage and Frequency 230/400 V ~ 50 Hz
Max. absorption: 10000 W
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint CP9VP6 DE HA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint CP9VP6 DE HA in the language / languages: English, German, Dutch, Spanish as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info