Manual Hotpoint-Ariston TVF651 (page 8 of 72) (English, French, Italian, Portuguese, Spanish)

105771

Zoom out

Zoom in

1/72

●

DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for

a drying programme.

The delay time is displayed in hours and counts down

each minute.

The time to end is displayed in hours and minutes and

counts down each minute, this includes the cool

tumble phase. When timed programmes are selected

the time displayed throughout the cycle is the actual

time remaining.

When a sensing programme is selected the time

displayed is an estimate of the time remaining. When

the programme is selected the display shows the time

required to dry a full load, after around 10 minutes the

controller calculates a better estimate of the cycle time.

The colons between the hours and minutes in the

display flash to show that the time is counting down.

When the programme finishes its cool tumble phase

the display will show .

The display also shows if there is a problem with your

dryer, if this occurs the display will show F followed by

a fault code number (see Troubleshooting).

●

Door Opening

Opening the door (or pressing the START/PAUSE

button ) during a programme will stop the dryer and

have the following effects:

●

The START/PAUSE light flashes Amber.

●

During a delay phase the delay will continue to

count down. The START/PAUSE button must

be pressed to resume the delay programme. The

progress lights will change to show current status.

●

During the drying part of the programme, the

time to end count continues but the colons do not

flash. The START/PAUSE button must be

pressed to resume the programme. The progress

lights will change to show the current status.

●

During the post creasecare phase of a drying

programme, the programme will finish. Pressing

the START/PAUSE button will re-start a new

programme at the beginning.

●

The START/PAUSE button must be pressed to

resume the programme. The progress lights will

change to show the current status and the

START/PAUSE light will stop flashing and turn green.

●

Changing the programmes knob will select a new

programme and the START/PAUSE light will flash

green. You can use this to select the Cool Tumble

programme to cool the clothes, if you find them

dry enough. Press the START/PAUSE button to

begin a new programme.

●

Note

If you have a power cut, switch off the power or

remove the plug. When the power is restored, press

the START/PAUSE button and the programme will

resume.

●

PROGRAMMES knob

! Warning, if after pressing the START/PAUSE button

the programme knob position has changed, the new

position will NOT change the programme selected.

To change a selected programme, press the

START/PAUSE button , the light flashes Amber to

indicate the programme is paused. Select the new

programme and any options required, the light will

then flash green. Press the START/PAUSE button

again and the new programme will start.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programme knob before

an option can be selected. Not all options are available

for all programmes (see Start and Programmes). If an

option is not available and you press the button, the

buzzer will beep three times. If the option is available

there will be one beep and the option light next to the

button lights to confirm the selection.

After the START/PAUSE button has been pressed only

the Pre Creasecare and Post Creasecare options can

be changed.

Time Delay

The start of some programmes (see Start and

Programmes) can be delayed for up to 24 hours.

Press this button, the display shows and the

option light comes on. Press again and a 1 hour delay

is selected and the display indicates 1hr, each further

press of the button adds 1hr to the delay. When 24hr

is displayed a further press the display shows

and after a couple of seconds cancels the delay. You

can also cancel the delay by pressing the ON/OFF

button.

Pre Creasecare

This option is only available if a delayed start has

been selected. It tumbles the clothes occasionally

during the delayed period to help prevent creases

developing.

High Heat

Available for Timed Drying programmes. Press this

button and a high heat setting is selected and the

light next to the button comes on.

Timed programmes have a default of low heat, if the

light next to the button is on then pressing this button

selects a low heat setting and the light goes out.

Post Creasecare

When available and selected, the clothes are

occasionally tumbled after the end of the drying and

cool tumble cycles, to help prevent creases

developing should you not be available to remove the

load immediately the programme is complete.

OFF

E88

The Controls

Start and Programmes

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston TVF651 in the language / languages: English, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston TVF651 Manual

Product: