Manual Hotpoint-Ariston TCUD 97B (page 14 of 20) (English)

665356

Zoom out

Zoom in

1/20

Start and Programmes

! Warning, after pressing the Start/Pause button , the

programme cannot be changed.

To change a selected programme, press the Start/Pause

button , the light flashes Amber to indicate the

programme is paused. Select the new programme and

any options required, the light will then flash green. Press

the Start/Pause button again and the new programme

will start.

●

Option buttons

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected, by pressing a programme selection

button, before an option can be selected. Not all options

are available for all programmes (see Programmes

Ta bl e). If an option is not available and you press the button,

the buzzer will beep 3 times. If the option is available the

indicator, on the display unit next to the bottom buttons,

lights to show that the option has been selected.

Delay Timer (Time Delay)

The start of some programmes (see The Display and

Programmes tables) can be delayed for up to 24 hours.

Ensure the water container is emptied before setting a

delayed start.

Pre Care

This option is only available if a delayed start has been

selected. It tumbles the clothes occasionally during the

delayed period to help prevent creases developing.

Post Care

When available and selected, the clothes are

occasionally tumbled after the end of the drying and cool

tumble cycles, to help prevent creases developing

should you not be available to remove the load

immediately the programme is complete.

Note: The Start/Pause light flashes Amber during this phase.

Note: If you have selected the Sound option this option is

not available.

Heat Level button, Display and Icons

Not all programmes allow you to change the heat level

and some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the display briefly shows

the selected heat level, along with a display of the selected

level icon:

HIGH HEAT MEDIUM HEAT LOW HEAT

Sound

When available and selected, a buzzer gives a signal at

the end of the drying cycle, to remind you that the

clothes are ready to be removed.

Note: If you have selected the Post Care option this

option is not available.

The Controls

88:88

Less Fluff

By reducing the mechanical action during the final drying

stage the amount of lint and fluff produced is substantially

reduced, protecting the fibres of your garments.

●

TIME DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for a

drying programme (see The Display).

The display also shows if there is a problem with your

dryer, if this occurs the display will show F followed by a

fault code number (see Troubleshooting).

●

Empty Water Container

(Messages about emptying can be ignored if you have

plumbed your dryer into a drain as there is no need to

empty the water container).

Messages are displayed to reminds you to empty the

water container (see The Display).

If the water container fills during a programme, the heater

turns off and the dryer does a period of Cool Tumble.

After this it stops and a message tells you to

EMPTY THE WATER CONTAINER .

You must empty the water container and restart the dryer

or the clothes will not dry. After re-starting the dryer the

message will take a few seconds to go out.

To avoid this always empty the water container each time

you use the dryer (see Maintenance).

●

Door Opening

Opening the door during a programme will stop the dryer

and have the following effects:

Note: The Start/Pause light flashes Amber during the Post

Care phase of a programme.

●

The display shows PAUSE .

●

During a delay phase the delay will continue to count

down. The Start/Pause button must be pressed to

resume the delay programme.

The display will change to show current status.

●

During the drying part of the programme, the colons

on the display stop flashing to show that the time has

stopped counting down.

The Start/Pause button must be pressed to resume

the programme. The display will change to show the

current status, the colons flash and count down

continues.

●

During the Post Care phase, the programme ends.

Pressing the Start/Pause button will restart a new

programme from the beginning.

●

Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, press and hold the

On/Off button until the display briefly shows

POWER ON

and the dryer reactivates. Then press the Start/Pause

button and the programme will resume.

Easy Iron Programme

‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which

fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The

cycle relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Synthetics 2kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles

and put them away in the closet. Should this not be possible repeat the programme.

The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,

and less well on acrylic fibres and on materials such as Tencel®.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston TCUD 97B in the language / languages: English as an attachment in your email.

The manual is 1,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston TCUD 97B Manual

Product: