Manual Hotpoint-Ariston ST 328 A HA (page 21 of 84) (English, German, Dutch, French, Italian, Portuguese, Spanish)

479318

Zoom out

Zoom in

1/84

Rinse aid and refined salt

Only use products which have been specifically

designed for dishwashers.

Do not use table salt or industrial salt, or washing

up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

rinse aid; however, we recommend that you add salt, especially

if you live in an area where the water is hard or very hard.

Follow the instructions given on the packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights remain

lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs

off surfaces more readily and therefore does not leave streaks or

marks.

The rinse aid dispenser should be filled:

• When the LOW RINSE AID

* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning

the lid (G) in an anticlockwise

direction.

2. Pour in the rinse aid, making sure

it does not overflow from the

dispenser. If this happens, clean

the spill immediately with a dry

cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Use a screwdriver to

turn the dosage adjuster (F) to one of the 6 pre-set positions (the

default position is set to 4):

• If there are streaks on the crockery, set the adjustment device

to a lower number (1-3).

• If drops of water remain on the crockery or if there are limescale

marks present after the cycle has finished, set the adjuster to a

higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash the

crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the water

hardness level in your area. This information can be obtained

from the organisation which supplies your household with water.

- Open the door and switch on the machine by pressing the ON/

OFF button.

- Press the P button and hold for approximately 5 seconds; two

short beeps will sound and the set hardness number will flash

slowly on the display (the water softening system is set to number

3).

- Press the P button repeatedly until the desired hardness level

has been reached (1-2-3-4-5

see Water hardness table

- To exit the function, wait a few seconds or press one of the

option buttons

*, or switch off the machine using the ON/OFF

button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees - mmol/l = millimoles per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash cycle,

make sure that the dispenser is never empty. Refined salt removes

limescale from the water, thus avoiding the formation of deposits

on crockery.

The salt dispenser is located in the lower part of the dishwasher

(

see Description

) and should be filled:

• When the green float

* cannot be seen by simply looking at the

cap of the salt dispenser.

• When the LOW SALT

* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel

* (

see figure)

and fill

the salt container right up to its edge (this

should hold approximately 1 kg); it is not unusual for a little water

to leak out.

4. Remove the funnel

* and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it on,

the head facing downwards so as to let the water flow out of the

four cracks which are arranged in a star shape on the lower part

of the cap. (Salt cap with green float

It is advisable to perform this procedure every time you add

salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash cycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt container

capacity duration

Level

°dH

°fH

mmol/l

months

1 0 - 6 0 - 10 0 - 1

7 months

2 6 - 11 11 - 20 1,1 - 2

5 months

3 12 - 17 21 - 30 2,1 - 3

3 months

4 17 - 34 31 - 60 3,1 - 6

2 months

34 - 50

61 - 90

6,1 - 9

2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt

. *

this setting may cause a slight increase in the

duration of

the cycles.

for 1 wash cycle per day.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston ST 328 A HA in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston ST 328 A HA Manual

Product: