Manual Hotpoint-Ariston sds1721v ha (page 19 of 64) (English, German, Dutch, French, Italian)

349223

Zoom out

Zoom in

1/64

Installation

! Before placing your new appliance into operation please read

these operating instructions carefully. They contain important

information for safe use, for installation and for care of the

appliance.

! Please keep these operating instructions for future reference.

Pass them on to possible new owners of the appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.

2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to

operate correctly and save energy.

3. Leave a space of at least 10 cm between the top part of the

appliance and any furniture above it, and at least 5 cm

between the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat (direct

sunlight, electric stove, etc.).

5. In order to maintain the correct distance between the

appliance and the wall behind it, fit the spacers supplied in

the installation kit, following the instructions provided.

Levelling

1. Install the appliance on a level and rigid floor.

2. If the floor is not perfectly horizontal, adjust the refrigerator by

tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it

vertically and wait at least 3 hours before connecting it to the

electricity mains. Before inserting the plug into the electrical

socket ensure the following:

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located on the

bottom left side of the fridge (e.g. 150 W).

• The voltage must be in the range between the values

indicated on the data plate located on the bottom left side

(e.g. 220-240V).

• The socket is compatible with the plug of the appliance. If the

socket is incompatible with the plug, ask an authorised

technician to replace it (

see Assistance

). Do not use

extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable

and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

The manufactur The manufactur

The manufactur

er declines any liability should these safetyer declines any liability should these safety

er declines any liability should these safety

measurmeasur

measur

es not be observed.es not be observed.

es not be observed.

Stability bracket

WARNING: To prevent the fridge from tilting forwards, it must be

held in place with the stability bracket supplied.

This is the responsibility of the customer.

Fixed to the floor or wall at the rear of the fridge, the stability

bracket hooks onto the compressor mounting plate holding the

fridge secure.

The stability bracket must be installed securely in

accordance with these instructions BEFORE using the

fridge.

Note: The fridge is heavy so care must be taken when

moving it.

1. Position the fridge in its chosen location.

2. Looking from the front of the fridge, mark the position of the left

hand panel.

3. Move the fridge far enough away to get clear access to the

back wall.

4. In order to clear components on the compressor mounting

plate, the stability bracket must be positioned on the floor

between 100 - 200mm to the right of the left hand panel mark.

5. Mark and drill the fixing holes and insert suitable fixings to

hold the bracket firm.

6. Carefully re-position the fridge. Make sure that the compressor

mounting plate locates into the stability bracket.

Start-up and use

Starting the appliance

! Before starting the appliance, follow the installation

instructions (see Installation).

! Before connecting the appliance, clean the compartments and

accessories well with lukewarm water and bicarbonate.

Using the refrigerator to its full potential

The temperature inside the refrigerator compartment

automatically adjusts itself according to the position of the

thermostat knob.

1 = warmest MAX = coldest

We recommend, however, a medium position.

The cooling section of the refrigerator is located inside the back

wall of the refrigerator compartment for increased space and

improved aesthetics. During operation, the back wall will be

covered in frost or water droplets depending on whether the

compressor is operating or paused. Do not worry, the refrigerator

is functioning normally.

If the TEMPERATURE ADJUSTMENT knob has been set on high

values with large quantities of food and with a high ambient

temperature, the appliance can operate continuously, resulting in

excessive frost formation and excessive energy consumption:

compensate for this by shifting the knob towards lower values

(defrosting will occur automatically).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston sds1721v ha in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston sds1721v ha Manual

Product: