Manual Hotpoint-Ariston RPD 9467 J (page 10 of 16) (English)

665257

Zoom out

Zoom in

1/16

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the On/Off

button ; the text HOTPOINT will appear on the display

and the START/PAUSE indicator light will flash slowly in

a green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

3. MEASURE OUT THE DETERGENT. Open the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle; the

name of the wash cycle will appear on the display. A

temperature and spin speed is set for each wash cycle;

these may be adjusted. The duration of the cycle will

appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin speed.

The machine automatically selects the maximum

temperature and spin speed set for the selected wash

cycle; these values cannot therefore be increased.

The temperature can be decreased by pressing the

button, until the cold wash (the display will visualise the

“--” symbol) setting is reached. The spin speed may be

progressively reduced by pressing the button, until

it is completely excluded (the display will visualise the

“--” symbol). If these buttons are pressed again, the

maximum values are restored.

! Exception: if the 2 programme is selected, the

temperature can be increased up to a value of 40°C.

! Exception: if the 3 programme is selected, the

temperature can be increased up to a value of 90°C.

! Exception: if the 4 programme is selected, the

temperature can be increased up to a value of 60°C..

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. To remove the

delayed start function press the button until the text

“-- h” appears on the display.

Set the rinse type.

Option makes it possible to select the desired

rinse type for sensitive skin. Press the button once for

the “Extra +1” level, which makes it possible to select

an additional rinse after the standard cycle rinse and

remove all traces of detergent. Press the button again

for the “Extra +2” level, which makes it possible to

select two additional rinses to the standard cycle rinses;

it is recommended for very sensitive skin. When the

button is pressed for the third time, the “Extra +3” level

is set, thus allowing the selection of 3 rinses in addition

to the standard cycle’s rinses. The option - started with

cycles at a temperature of 40°C - makes it possible to

remove major allergens such as pollen, cat and dog

hair. With cycles at a temperature higher than 40° a very

good level of antiallergic protection is achieved. Press

the button again to go back to the “Normal rinse” rinse

type. If the current adjustment can be neither set nor

changed, the display will show “No Selection” or “No

Change”.

Modifying the cycle settings.

• Press the button to enable the function; the relevant

indicator light on the display will light up.

• Press the button again to disable the function; the

relevant indicator light on the display will switch off.

! If the selected function is incompatible with the set

programme, the relevant indicator light will appear dimly

lit; in addition, the incompatibility will be signalled by a

buzzer (3 beeps) and the wording “No Selection” will

appear on the display.

! If the selected function is incompatible with another

previously set function, the wording “No Selection”

will appear on the display and the function will not be

enabled.

! The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol will

be on). During the wash cycle, the name of the phase in

progress will appear on the display. To change a wash

cycle while it is in progress, pause the washing machine

using the START/PAUSE button (the START/PAUSE

indicator light will flash slowly in an orange colour);

then select the desired cycle and press the START/

PAUSE button again. To open the door while a cycle

is in progress, press the START/PAUSE button; if the

DOOR LOCKED symbol is switched off the door

may be opened. Press the START/PAUSE button again

to restart the wash cycle from the point at which it was

interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “CYCLE END” on the display;

when the DOOR LOCKED symbol switches off

the door may be opened. Open the door, unload the

laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

Direct Injection

The washing machine is equipped with the innovative

technology «Direct Injection» which pre-mixes water and

detergent, thus immediately activating the detergent’s

cleaning principles. This active emulsion is directly

introduced into the drum of the washing machine and

penetrates the fibres with more efficacy in cleaning

even heavily soiled garments at low temperatures, fully

preserving colours and fabrics.

The mode «Power» ensures the best cleaning performance

and the mode «EcoEnergy» allows more energy saving.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston RPD 9467 J in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston RPD 9467 J Manual

Product: