Manual Hotpoint-Ariston MH 99.1 (page 14 of 80) (English, German, Dutch, French, Italian, Portuguese, Spanish)

479521

Zoom out

Zoom in

1/80

Installation

ImportantImportant

Important: The power supply to the appliance must

be cut off before any adjustments or maintenance

work is done on it.

Installation of Built-in Ovens

To ensure the proper working order of the built-in

appliance, the kitchen unit must be of a suitable size.

The sizes of the unit for installing the cooker under a

worktop or in a column unit are shown in figure.

min. 45 mm.

To provide adequate ventilation, there must be

appropriate ventilation openings in the front bottom

and the top part of the cabinet (an intake opening on

the bottom of at least 200 cm2, and an exhaust

opening of at least 90 cm2). The unit panels next to

the cooker must be heat resistant. In the case of

veneered wood units, glues must be resistant to a

temperature of 120 °C. In accordance with safety

standards, once the appliance has been mounted,

there must be no possible contact with electrical

parts. Any protective parts must be secured so that

they can only be removed with the use of tools.

Fastening the oven

Insert the appliance into the compartment; open the

oven door and fasten the oven to the cabinet using

the four screws “A”, remembering to place the

special spacers provided between the hole and the

screw itself.

447

in.

550

472 mm

475 mm

860 mm

22 mm

895 mm

525

469 mm

850 mm

Electrical Connection

Those ovens equipped with a three-pole power

supply cable are designed to operate with an

alternating current with the voltage and frequency

indicated on the data plate (located on the

appliance) and in the instruction manual. The wire for

earthing the appliance is yellow-green in colour.

Replacing the cable

Use a rubber cable of the type H05VV-F with a

suitable cross section 3 x 1.5 mm².

The yellow-green earth wire must be 2-3 cm

longer than the other wires.

Opening the terminal board:

• Using a screwdriver, prise on the side tabs of the

terminal board cover;

• Pull open the cover of the terminal board.

To install the cable, proceed as follows:

• Remove the wire clamp screw and the three

contact screws L-N-

• Fasten the wires beneath the screwheads using

the following colour scheme: Blue (N) Brown (L)

Yellow-Green

• Fasten the supply cable in place with the clamp

and close the cover of the terminal board.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston MH 99.1 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston MH 99.1 Manual

Product: