Manual Hotpoint-Ariston LL 68 FR (page 20 of 24) (English, French)

512985

Zoom out

Zoom in

1/24

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

Installation and moving

After having bought or moved your dishwasher to another home, a

correct installation ensures that your dishwasher will operate

smoothly and efficiently.

Hot water connection.

Your dishwasher can be supplied

with hot water from the mains

supply (if you have a central heating

system with radiators) at a tempe-

rature of no more than 60°C.

In this case, the wash cycle time

will be about 15 minutes shorter

and the wash will be slightly less

effective.

The connection must be made to

hot water supply following the

same procedures as those indicated

for the cold water connection.

Drain hose connection.

Fit the drain pipe into a drain line

with a minimum diameter of 4 cm

or place it over the sink. Avoid

restricting or bending it. Use the

special plastic elbow provided (see

figure) to position it in the best

possible way. The part of the pipe

marked with the letter A should be

between 40 and 100 cm above the

ground.

The pipe should not be immersed

in water.

Electrical connection.

First of all, check that the mains

voltage and frequency values

correspond to those stated on the

rating plate located on the stainless

steel inner door of the appliance

and that the electrical system to

which the dishwasher is connected

is sized for the maximum current

indicated on said rating plate.

Earth: indispensable

safety.

Only now can you plug the

appliance into a socket provided

with an efficient earth connection

(the system's earthing is a

guarantee of safety provided for by

law, make sure your system has

it).

Choose where you want to install

your dishwasher, you can even

place it so that its sides or back

panel are side by side with furniture

or up against the wall. The

dishwasher is provided with water

supply and drain hoses, which can

be directed towards the left or right

to facilitate appropriate

installation.

This dishwasher model can be built

under a single worktop (please read

the relevant instruction sheet).

Levelling.

Once the appliance is positioned,

adjust the feet by screwing them in

or out depending on how high you

want it and to level it so that it is

horizontal. Make sure that it is not

inclined more than 2 degrees. If the

appliance is level, it will help ensure

its correct operation.

Anti-flooding protection

Your dishwasher is provided with a

special system which blocks the

water supply in the event of leaks

inside the appliance.

Cold water connection.

This electric household appliance

should be connected to the water

mains using the cold water supply

hose provided with the appliance

only. Do not use a different hose. In

the event of replacements, use

original spare parts only.

Connect the cold water supply

hose to a 3/4 gas and taking care

to screw it tightly onto the tap. If

the water hoses are new or have

been out of use for an extended

period of time, let the water run to

make sure it is clear and free of

impurities before making the

connection. If this precaution is not

taken, the water inlet could get

blocked, causing damage to your

dishwasher.

Your dishwasher has arrived

The special

plastic elbow

should be

fastened firmly

onto the wall to

prevent the drain

hose from

moving and

allowing water to

spill outside the

drain.

Power supply wire.

Check the power supply wire on a

regular basis; if it is damaged, we

recommend you have it replaced

by an authorised technical

Assistance service centre.

The plug

The dishwasher plug must be

accessible so that maintenance

can be done safely.

If the power

socket to which

the appliance is

connected is not

compatible with

the plug, replace

it with a suitable

plug rather than

using adapters or

multiple plugs as

these could cause

overheating or

burns.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LL 68 FR in the language / languages: English, French as an attachment in your email.

The manual is 4,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston LL 68 FR Manual

Product: