Manual Hotpoint-Ariston LL 65 X FR (page 16 of 24) (English, French)

512984

Zoom out

Zoom in

1/24

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

You have loaded your dishes and you now have to set the

wash cycle. It takes just one minute to learn how

Starting the dishwasher

Ready, steady, go!

First of all.

Turn on the water tap com-

pletely and press ON-OFF

button "A". you will hear a short

beep and indicator light "B"

lights up. Now the appliance is

on and awaiting instructions.

Selecting the wash

cycle.

Select the wash cycle by

pressing button "P". Each time

you press the button, a beep

will sound and indicator lights

"E" will light up in sequence:

choose the cycle you deem

most suited to the type of

dishes to be washed (take a

look at page 16, where you will

find the wash cycle table). If the

appliance door is shut, press

the Start button "R" and you will

hear a beep; the cycle will start

up within a few seconds.

The dishwasher informs

you.

Your dishwasher is fitted with

indicator lights (G) which light

up to indicate the cycle phase

under way.

Here are the symbols corre-

sponding to each cycle phase:

pre-wash, wash, rinses, drying.

At all times, your dishwasher

tells you which cycle phase is

under way.

Modifying a wash cycle

in progress.

But if you have chosen the

wrong cycle, not to worry! You

can modify the wash cycle in

progress, if it has only just

started. Keep the RESET

button "R" pressed for about 5

seconds: a prolonged beep will

sound, followed by three short

beeps. Indicator light "G" will

turn off and at this stage, all the

settings will have been

cancelled. You are now free to

re-set the correct wash cycle.

You've left out a dish?

Well, it happens to everyone. In-

terrupt the wash cycle by press-

ing the ON-OFF button, insert

the dish you had forgotten and

press the ON-OFF button again.

The cycle will start up from

where you interrupted it.

Finished?

The end of the wash cycle is in-

dicated by two short beeps and

the flashing of the drying phase

indicator light.

Caution

Turn the appliance off by pressing

button "A", unplug the appliance

from the electricity socket to cut

off the power supply; the power

supply cable should consequently

be easily accessible.

 Turn off the water tap.

 Wait a few minutes before unload-

ing the dishes: they are very

hot! If you wait a little while, they

dry better thanks to the steam.

 Empty the lower rack first.

There's been a power

failure? Have you

opened the dishwasher

door?

The wash cycle stops and then

restarts when the electricity

comes back on or when you

shut the door. Everything is

under control!

You decide when it

starts.

When you have loaded the

dishes, you can choose when to

start your dishwasher before

setting the wash cycle desired.

Press button "D" to delay the

start of the wash cycle by 12, 9,

6 or 3 hours. Each time you

press it, you will hear a short

beep and the indicator light "G"

corresponding to the selected

delay will light up.

Now you can select the desired

wash cycle. Press the start but-

ton "R" and after you hear the

beep, the countdown to the de-

layed start will begin.

Once this time is up, the indicator

light will stop flashing and the wash

cycle will begin.

If you have set a 12 hour delay,

for example, once you have

selected the wash cycle, the 12

hour indicator light will flash

followed by the others in

sequence until the set time

delay is up. A quick look at the

indicator lights will keep you

informed of the countdown

progress at all times.

Have you changed your

mind?

If you change your mind, you

can set a shorter time delay:

press button "D" to select it. You

need not reset the wash cycle.

If on the other hand you want

to cancel the delay set and you

want the cycle to start

immediately, press button "D"

repeatedly until the cycle starts

and indicator light "G"

corresponding to the cycle start

phase comes on.

Dual function of

indicator lights "G"

1) flashing to indicate a

delayed start: to remind you

that you have set a delayed

start;

2) on and not flashing

beneath the cycle phase

symbol:

meaning the cycle has started

and is in the phase indicated by

the symbol.

You want to wash on

one rack only?

Remember to use half

the amount of

detergent.

If you only have a few dishes to

wash, you can decide to run a half-

load, to save on water, electricity

and detergent. Before setting any

wash cycle whatsoever, press but-

ton "F", indicator light "H" will light

up and your dishwasher will wash

on the upper rack only.

Would you like to see

which settings you

have made?

At any time, when the cycle is

under way, if you press button

"P", the cycle in progress

indicator light will light up for

a few seconds, followed by the

half load indicator light,

wherever set.

If opening the door

soon after the end of

the programme,or

during it, stand away

from the Dishwasher,

to avoid possible

injury from hot

steam.

Make sure the wash

cycle has ended

before removing the

dishes!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LL 65 X FR in the language / languages: English, French as an attachment in your email.

The manual is 8,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston LL 65 X FR Manual

Product: