75130
17
Zoom out
Zoom in
Previous page
1/80
Next page
ARISTON DISHWASHER - Instructions for installation and use
15
D
ISHWASHER
You have loaded your dishes and you now have to set the
wash cycle. It takes just one minute to learn how
Starting the dishwasher
Ready, steady, go!
You can cancel the
wash cycle in
progress, if it has
only just started.
Make sure the wash
cycle has ended
before removing the
dishes!
If opening the door
soon after the end of
the programme,or
during it, stand away
from the Dishwasher,
to avoid possible
injury from hot
steam.
Do you want extra
drying?
Press button "E" before you
start the selected wash cycle.
A prolonged beep will inform
you that you have selected ex-
tra drying, a short beep
indicates it has been disabled.
With extra drying, the wash
cycle will last longer, to provide
you with drier dishes.
First of all.
After performing all the operations
described in the previous para-
graphs, turn the water tap on com-
pletely, open the appliance door and
press ON-OFF button "A": indica-
tor light "B" comes on. Your appli-
ance is now on and awaiting instruc-
tions.
Selecting the wash
cycle.
Select the wash cycle by pressing
button "P". Each time this button
is pressed, one of the indicator
lights "M" will come on in sequence,
select the wash cycle you deem
most suitable for the type of dishes
to wash (take a look at page 17,
where you will find the wash cycle
table). Close the appliance door and
after a few seconds, you will hear
a short beep: the wash cycle has
begun.
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Open the appli-
ance door carefully to avoid any
hot water splashes, then keep but-
ton "P" pressed for approximately
5 seconds, until you hear 3 short
beeps. Indicator light "M" will come
off and at this point, all the settings
will have been cancelled. You are
now free to re-set the correct wash
cycle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by opening the
appliance door with the utmost
care, as usual, then insert the dish
you had forgotten. When you shut
the appliance door, the cycle will
start up from where you interrupted
it.
Finished?
The end of the wash cycle is indi-
cated by a double beep and the
flashing of the wash cycle indicator
light "M".
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry
better thanks to the steam.
Empty the lower rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity comes
back on or when you close the door.
Everything is under control!
Warning!
Open the dishwasher door,
turn off by pressing button A,
unplug the appliance from the
electricity socket to cut off the
power supply; the power supply
cable should consequently be
easily accessible.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint-Ariston LI 671 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LI 671 A in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 17,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info