Manual Hotpoint-Ariston li 480 a c (page 21 of 80) (English, German, Dutch, French, Italian, Portuguese, Spanish)

127242

Zoom out

Zoom in

1/80

ARISTON DISHWASHER - Instructions for installation and use

1509)50-4

If the power

socket to which

the appliance is

connected is not

compatible with

the plug, replace

it with a suitable

plug rather than

using adapters or

multiple plugs as

these could cause

overheating or

burns.

Installation and moving

After having bought or moved your dishwasher to another home, a correct

installation ensures that your dishwasher will operate smoothly and efficiently.

Your dishwasher has arrived

service technician (see

Service).

Hot water connection.

Your dishwasher can be

supplied with hot water

from the mains supply (if

you have a central heating

system with radiators) at a

temperature of no more

than 60°C.

In this case, the wash cycle

time will be about 15

minutes shorter and the

wash will be slightly less

effective.

The connection must be

made to hot water supply

following the same

procedures as those

indicated for the cold water

connection.

Anti-flooding protection

Your dishwasher is provided

with a special system which

blocks the water supply in

the event of leaks inside the

appliance. It is further

equipped with a water inlet

hose that can withstand

extremely high pressures

and that turns bright red in

the event of breakage.

Safety in the event of flood-

ing is ensured by the second

clear hose that contains the

former and thus highlights

the latter when it has

turned bright red. It is vi-

tal that you check it on a

regular basis: if you see it

has turned bright red, then

you know you have to re-

place it as soon as possible.

Call for an authorised tech-

nical engineer to come and

replace it.

Drain hose connection.

Fit the drain pipe into a

drain line with a minimum

diameter of 4 cm or place it

over the sink. Avoid restrict-

ing or bending it. The part

of the pipe marked with the

letter A should be between

40 and 100 cm above the

ground.

The pipe should not be im-

mersed in water.

Electrical connection.

First of all, check that the

mains voltage and

frequency values

correspond to those stated

on the rating plate located

on the stainless steel inner

door of the appliance and

that the electrical system to

which the dishwasher is

connected is sized for the

maximum current

indicated on said rating

plate.

Earth: indispensable

safety.

Only now can you plug the

appliance into a socket

provided with an efficient

earth connection (the

system's earthing is a

guarantee of safety provided

for by law, make sure your

system has it).

Choose where you want to

install your dishwasher,

you can even place it so that

its sides or back panel are

side by side with furniture

or up against the wall. The

dishwasher is provided with

water supply and drain

hoses, which can be directed

towards the left or right to

facilitate appropriate

installation.

Levelling.

Once the appliance is

positioned, adjust the feet

by screwing them in or out

depending on how high you

want it and to level it so that

it is horizontal. Make sure

that it is not inclined more

than 2 degrees. If the

appliance is level, it will he

lp ensure its correct

operation.

Adjusting the Back Feet

Insert the appliance into the

cutout and then adjust the

height using the screws

located on the front bottom

part of the machine. Use a

screwdriver to turn the

screws in the clockwise or

anti-clockwise direction to

increase or decrease the

height respectively.

Cold water connection.

Connect the cold water

supply hose to a 3/4 gas

threaded connection, taking

care to screw it tightly onto

the tap. If the water hoses

are new or have been out of

use for an extended period

of time, let the water run to

make sure it is clear and

free of impurities before

making the connection. If

this precaution is not taken,

the water inlet could get

blocked, causing damage to

your dishwasher.

-It is strongly recommended

to use a new hose to connect

the dishwasher to the water

supply line, and the old

hose-set should not be

reused. Asking to specilized

shop or an authorized

Condensation-proof tape.

On some models, a

transparent condensation-

proof adhesive tape has been

provided.

It should be stuck onto the

lower side of your wooden

worktop to protect it from

the formation of

condensation.

When not provided, this tape

can be requested as a spare

part from authorised

retailers.

Attention

- Once the appliance has

been installed, the electrical

plug and socket should re-

main accessible.

- If the power supply cable

is damaged, it must be

replaced by the

manufacturer or its

Technical Assistance

Service in order to prevent

all potential hazards. (See

Assistance)

- The cable should not be

bent or compressed.

- The Company shall not be

held responsible for any

incidents that occur if these

regulations are not

observed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston li 480 a c in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 33,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston li 480 a c Manual

Product: