Manual Hotpoint-Ariston LFT 228 A-HA (page 18 of 84) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

71668

Zoom out

Zoom in

1/84

&

Start-up and use

Starting the dishwasher

1. Turn the water tap on.

2. Open the door and press the ON/OFF button: you will hear

a short beep and the display and option indicator lights switch

on.

3. Measure out the detergent (see below).

4. Load the racks (see Loading the racks).

5. Select the wash cycle in accordance with the type of

crockery and its soil level (see Table of wash cycles),

pressing the P button.

6. Select the wash options (see adjacent information).

7. Start the wash cycle by shutting the door: a long beep

signals the start of the wash cycle.

8. Two short beeps and one long one indicate the end of the

wash cycle and the wash cycle number flashes on the display.

Open the door, switch off the appliance by pressing the ON/

OFF button, shut off the water tap and unplug the appliance

from the electricity socket.

9. Wait for a few minutes before removing the crockery, in

order to avoid burns. Unload the racks, beginning with the

lower level.

The order in which the different wash cycles are displayed

will change according to the frequency with which each cycle

is used.

AUTO WASH CYCLES

*: this model of dishwasher is

equipped with a special sensor which can be used to assess

the level of soiling and automatically select the most efficient

and economic wash cycle accordingly.

The duration of the auto wash cycles may vary due to the

operation of the sensor.

If the crockery is only lightly soiled or if it has been rinsed

with water before being placed in the dishwasher, reduce the

amount of detergent used accordingly.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that it has

only just begun: open the door, avoiding the escaping steam,

and press and hold the ON/OFF button; the machine will

switch off with a long beep. Switch the machine back on using

the ON/OFF button and select the new wash cycle and any

options desired; start the cycle by closing the door.

Adding extra crockery

Without switching off the machine, open the door, taking care

to avoid the escaping steam, and place the crockery inside

the dishwasher. Close the door: the cycle starts from the point

at which it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a

power cut, the cycle stops. It starts again from the point at

which it was interrupted once the door has been shut or once

the electricity supply is restored.

Measuring out the detergent

A good wash result also depends on the correct amount of

detergent being used; exceeding the stated amount does not

result in a more effective wash and increases environmental

pollution.

Only use detergent which has been

specifically designed for dishwashers.

 DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has ended.

The use of tablets is only recommended for

models which offer the MULTI-FUNCTIONAL

TABLETS option.

To achieve the best results from each washing

and drying cycle, powder detergent, rinse aid

liquid and salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing button

2. Pour in the detergent after

consulting the Table of wash cycles:

 For powder detergent use

compartments A and B.

 For detergent in tablet form: when

the cycle requires 1 tablet, place it in

compartment A and close the cover;

when it requires 2, place the second tablet at the bottom of the

appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

Wash options

If an option is not compatible with the selected was cycle

(see Table of wash cycles), the corresponding LED flashes

rapidly 3 times and 2 short beeps will sound.

Delayed start

It is possible to delay the start time of the cycle by 3, 6 or 9

hours.

1. Press the DELAYED START button: every time it is pressed

a buzzer sounds and the selected period of time is displayed.

2. Select the wash cycle and shut the door: after the beep

sounds, the timer begins counting down.

3. Once this time has elapsed, the indicator light switches off

and the wash cycle begins.

To adjust the delay time and select a smaller period of time,

press the DELAYED START button. To cancel it, press the

button repeatedly until the selected delayed start indicator

light switches off. The wash cycle will start automatically as

soon as the door is shut.

* Only available in selected models.

What is the opening on the right hand side of the opening door of a hotpoint LFT2284 T for ? Submitted on 14-9-2020 at 20:40
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LFT 228 A-HA in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 3,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston LFT 228 A-HA Manual

Product: