Manual Hotpoint-Ariston LFF 825 (page 9 of 84) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

76816

Zoom out

Zoom in

1/84

Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard

or very hard. Follow the instructions given on the

packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights

remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

 When the LOW RINSE AID

* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning the lid

(G) in an anticlockwise direction.

2. Pour in the rinse aid, making sure it

does not overflow from the dispenser. If

this happens, clean the spill immediately

with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly

into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results,

you may adjust the quantity of rinse aid used. Use a

screwdriver to turn the dosage adjuster (F) to one of the 6

pre-set positions (the default position is set to 4):

 If there are streaks on the crockery, set the adjustment

device to a lower number (1-3).

 If drops of water remain on the crockery or if there are

limescale marks present after the cycle has finished, set

the adjuster to a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

- Switch on the appliance by pressing the ON/OFF button.

- Press the P button and hold for a few seconds; two short

beeps will sound and the wash cycle indicator light

corresponding to the set degree of hardness will flash slowly

on the control panel (the water softening system is set to

number 3).

- Press the P button repeatedly until the desired hardness

level has been reached (1-2-3-4-5

* see Water hardness

table).

E.g. Hardness level 1 (1

wash cycle indicator light flashes)

Hardness level 2 (1

wash cycle indicator light on, 2

wash

cycle indicator light flashes)

Hardness level 3 (1

and 2

wash cycle indicator lights on, 3

wash cycle indicator light flashes etc.) up to a maximum of

level 5*.

- To exit the function, wait approximately 30 seconds or switch

off the machine using the ON/OFF button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f =

hardness measured in French degrees - mmol/l = millimoles

per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty.

Refined salt removes limescale from the water, thus

avoiding the formation of deposits on crockery.

The salt dispenser is located in the lower part of the

dishwasher (see Description) and should be filled:

 When the green float* cannot be seen by simply looking at

the cap of the salt dispenser.

 When the LOW SALT* indicator light on the control panel is

illuminated;

1. Remove the lower rack and

unscrew the container cap

(anticlockwise).

2. The first time you do this: fill the

water tank right up to its edge.

3. Position the funnel

* (see figure) and

fill the salt container right up to its

edge (this should hold approximately

1 kg); it is not unusual for a little water to leak out.

4. Remove the funnel* and wipe any salt residue away from

the opening; rinse the cap under running water and then

screw it on, the head facing downwards so as to let the

water flow out of the four cracks which are arranged in a

star shape on the lower part of the cap. (the container cap

with the green float

It is advisable to perform this procedure every time you

add salt to the container.

Make sure the cap is screwed on tightly, so that no

detergent can get into the container during the wash cycle

(this could damage the water softener beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

* Only available in selected models.

Water Hardness Table

°dH °fH mmol/l level

0 6 0 10 0 1 1

6 11 11 20 1.1 2 2

12 17 21 30 2.1 3 3

17 34 31 60 3.1 6 4

34 50 61 90 6.1 9

For values between 0°f and 10°f, we do not

recommend the use of salt.

* this setting may cause a slight increase in the

duration of the cycle.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LFF 825 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 3,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston LFF 825 Manual

Product: