127648

Hotpoint-Ariston lff 8246 x fr ha Manual

24
Zoom out
Zoom in
Previous page
1/24
Next page
EN
"
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
Malfunction: Possible causes / Solutions:
The dishwasher does not start.
• The plug has not been inserted into the electrical socket properly, or
there is no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (
see Start-up and use
).
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet finished.
• The water outlet hose is bent (
see Installation
).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher makes
excessive noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to
the hardness of the water (
see Rinse aid and salt
).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish tinge.
• The rinse aid dosage is too high.
The crockery has not been
dried properly.
• A wash cycle without a drying programme has been selected.
• The rinse aid has been used up or the dosage is too low (
see Rinse aid
and salt
).
• The rinse aid dispenser setting is not high enough.
The dishes are not clean.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take
any water in/Tap shut-off alarm.
(several short beeps are emitted)
(The ON/OFF indicator light flashes and
the display shows A-6).
• There is no water in the mains supply.
• The water inlet hose is bent (
see Installation
).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken
when the beeps sounded. Switch off the machine using the ON/OFF
button, turn on the tap and switch the machine back on after 20
seconds by pressing the same button. Re-programme the machine and
restart the wash cycle.
Water intake solenoid valve
malfunction alarm
(The ON/OFF indicator light flashes and
the display shows A-2).
• Switch off the appliance by pressing the ON/OFF button and switch it
back on after one minute. If the alarm continues, shut off the water tap
to eliminate the risk of flooding, remove the plug from the electrical
socket and contact Assistance.
Water inlet hose alarm/Water
inlet filter blocked.
(the ON/OFF indicator light flashes and
the display shows A-7).
• Switch off the appliance by pressing the ON/OFF button. Shut off the
water tap to eliminate the risk of flooding and remove the plug from the
electrical socket.
Make sure the water inlet filter has not become blocked by various
impurities. (see “ Care and maintenance” chapter).
195067792.00
12/2007- Xerox Business Services
… 24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint-Ariston lff 8246 x fr ha at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston lff 8246 x fr ha in the language / languages: English, French as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info