570819

Hotpoint-Ariston LFB 5B019 Manual

17
Zoom out
Zoom in
Previous page
1/28
Next page
EN
17
Installation
* Only available in selected models.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto
its back.
Connecting the water supply
Adaptation of the water supply for installation should only
be performed by a qualified technician.
The water inlet and outlet hoses may be positioned towards
the right or the left in order to achieve the best possible
installation.
Make sure the dishwasher does not bend or squash the hoses.
Connecting the water inlet hose
• Toa3/4”gascoldor hotwaterconnectionpoint(max.
60°C).
• Runthewateruntilitisperfectlyclear.
• Screwtheinlethosetightlyintopositionandturnoffthe
tap.
If the inlet hose is not long enough, contact a specialist
store or an authorised technician
(seeAssistance)
.
The water pressure must be within the values indicated
in the Technical Data table - otherwise the dishwasher may
be function properly.
Make sure the hose is not bent or compressed.
Connecting the water outlet hose
Connect the outlet hose to a drain duct with a minimum
diameterof2cm.(A)
The outlet hose connection must be at a height ranging from
40to80cmfromthefloororsurfacewherethedishwasher
rests.
Before connecting the water outlet hose to the sink drain,
removetheplasticplug(B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water
supply in the event of anomalies or leaks from inside the
appliance.
Somemodelsare alsoequipped withthesupplementary
safety device New Acqua Stop*, which guarantees anti-
flooding protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstances should the water inlet hose be cut
as it contains live electrical parts.
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
• Thesocketis earthed and complies with current
regulations;
• thesocket canwithstand themaximumload ofthe
appliance as shown on the data plate located on the inside
of the door
(seechapterDescriptionoftheappliance);
• Thepowersupplyvoltagefallswithinthevaluesindicated
on the data plate on the inside of the door.
• Thesocketiscompatiblewiththeplugoftheappliance.If
this is not the case, ask an authorised technician to replace
theplug(
see Assistance
).Donotuseextensioncablesor
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced
by the manufacturer or its authorised Technical Assistance
Serviceinorder toprevent allpotential hazards.
(See
Assistance)
The Company shall not be held responsible for any
incidents, if these regulations are not observed.
Positioning and levelling
1. Position the dishwasher on a level sturdy floor. If the floor is
uneven, the front feet of the appliance may be adjusted until
itreachesahorizontalposition.Iftheapplianceislevelled
correctly, it will be more stable and much less likely to move
or cause vibrations and noise while it is operating.
2. Before recessing the dishwasher, stick the adhesive
transparent strip* under the wooden shelf in order to protect
it from any condensation which may form.
3.Placethedishwashersothatitssidesorbackpanelarein
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop*
(seethe
Assembly instruction sheet)
.
4*.Toadjusttheheightoftherearfoot,turntheredhexagonal
bushing on the lower central part at the front of the dishwasher
usingahexagonalspannerwithanopeningof8mm.Turnthe
spanner in a clockwise direction to increase the height and
in an anticlockwise direction to decrease it.
(seeBuilding-in
instruction sheet attached to the documentation)
MIN 40 cm
MAX 80 cm
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint-Ariston LFB 5B019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LFB 5B019 in the language / languages: English, Italian as an attachment in your email.

The manual is 5,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info