Manual Hotpoint-Ariston KBT 6124 ID IX (page 13 of 60) (German, Dutch, French, Italian, Portuguese, Spanish)

74116

Zoom out

Zoom in

1/60

40 mm min.

40mm

Opening of at least 5 mm

on the overall width

measurement of the surface.

Above an empty cabinet or a drawer

A space of at least 40 mm, or an opening of 5 mm on

the width measurement of the cabinet, should be created.

Connecting the hob

 The electrical safety of this appliance can only be

guaranteed if the latter is correctly and efficiently

earthed, in compliance with regulations on

electrical safety. Always ensure that this vital

safety measure has been taken. If you have any

doubts, call in a qualified technician to check the

electrical system thoroughly.

 The manufacturer denies all responsibility for

damage resulting from a system which has not

been earthed correctly.

 Before powering the appliance, check whether the

technical characteristics featured on the appliance

data plate correspond with those of the mains

electrical system.

 Check that the current load of the mains supply

and of the power sockets is suitable for the

maximum power of the appliance, indicated on

the appliance data plate. If in doubt, contact a

qualified professional.

Disconnect the appliance from the electricity

supply before all operations.

Connect your hob to the electrical system by means

of a

junction box:junction box:

junction box: if the appliance is connected

permanently to the mains, an

omnipolar circuitomnipolar circuit

omnipolar circuit

breakerbreaker

breaker, accessible if necessary, with a minimum

contact opening of 3 mm should be installed.

Valid only for models with a power supply

cable

Some models are supplied with a single-phase

power supply cable, and should consequently only

be connected to the single-phase mains. Observe

the wire colours, as indicated in the diagram

attached.

Valid only for models without a power supply

cable

Some models are not fitted with a power supply

cable, as the cable should be sized according to the

type of electrical connection in use (see connection

table below). To connect the cable, proceed as

follows:

1. Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(see diagram).

2. Loosen the cable

clamp screw and

remove it, using a

screwdriver as a lever

(see figure).

3. Remove the wire

contact screws L-N-

, then fasten the wires

under the screw heads,

respecting the colour

code: Blue (N), Brown

(L) and Yellow-Green

Verde (

 to make the desired electrical connection (see

table), use the jumpers housed inside the box.

Position the power supply cable wires according

to the indications in the table.

 once the connections have been made, tighten all

the terminal screws fully.

 Fasten the supply cable in place with the clamp

and close the cover of the terminal board.

Electrical connections Voltage, Frequency Fuses, Sections

FR-BE-AT-DE-GR-ES-IL-

IT-NZ-PT-GP-CH-MA-LU-

IE-FI-SE-IS-GB-NL-DK

230V - 1+N~ 50Hz

CY-MT-AU-NZ-KW

240V - 1+N~ 50Hz

25A *

2,5 mm²

FR-BE-NO

230V - 2 ~ 50Hz

BR=BRUN,BL=BLEU

BR=BRUIN, BL=BLAUW

BR=BRAUN, BL=BLAU

BR=BROWN, BL=BLUE

* Application of the simultaneity coefficient in accordance with

cei 60335-2-6 norm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston KBT 6124 ID IX in the language / languages: German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston KBT 6124 ID IX Manual

Product: