Manual Hotpoint-Ariston KBM 6001 H IX (page 21 of 42) (English, German, Dutch, French, Italian, Portuguese, Spanish)

511612

Zoom out

Zoom in

1/42

Technical characteristics

Electrical connection

• The electrical safety of this appliance can only be

guaranteed if the latter is correctly and efficiently

earthed, in compliance with regulations on electrical

safety. Always ensure that this vital safety measure has

been taken. If you have any doubts, call in a qualified

technician to check the electrical system thoroughly.

•

The manufacturer denies all responsibility for dam-

age resulting from a system which has not been

earthed correctly.

• Before powering the appliance, check whether the

technical characteristics featured on the appliance data

plate correspond with those of the mains electrical

system.

• Check that the current load of the mains supply and

of the power sockets is suitable for the maximum power

of the appliance, indicated on the appliance data plate.

If in doubt, contact a qualified professional.

Disconnect the appliance from the electricity supply

before all operations.

Connect your hob to the electrical system by means of a

junction box: if the appliance is connected permanently

to the mains, an omnipolar circuit breaker, accessible if

necessary, with a minimum contact opening of 3 mm

should be installed.

Single-phase connection

The hob is equipped with a preconnected electricity sup-

ply cable, which is designed for single-phase connection.

Connect the wires according to the instructions given in

the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

230V 1+N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L: brown and black

together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

• 400V - 2+N ~ 50 Hz

• 230V 3 ~ 50 Hz

• 400V - 2+2N ~ 50 Hz

Separate the wires and connect them according to the

instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

400V - 2+N ~

50 Hz

230V 3 ~

50Hz

: yellow/green;

N: the two blue wires together

L1: black

L2: brown

400V - 2+2N ~

50 Hz

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

If the mains supply corresponds with one of the following:

Voltage and mains frequency

• 400V 3 - N ~ 50 Hz

proceed as follows:

! The cable provided is not suitable for the following types

of installation.

1. Use a suitable supply cable, H05RR-F or higher, with

the right dimensions (cable section: 2.5 mm).

2. To open the terminal board, insert a screwdriver into

the side tabs of the cover and open it (

see Terminal board

picture

3. Loosen the cable clamp screw and the terminal board

screws according to the type of connection required and

position the connection supports as shown in the follow-

ing table and diagrams.

4. Position the wires according to the following table and

diagrams and connect the appliance by tightening all the

screws for the springs as much as possible.

Voltage and

mains frequency

Electrical connections Terminal board

400V 3-N ~ ı 50

Three-phase 400

5. Secure the power supply cable by fastening the cable

clamp screw, then put the cover back on.

U-bolt

connection support

Phase PhasePhase Neutral Earth

Three-phase 400

This appliance conforms with the following European

Community Directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

amendments;

- 89/336/EEC of 03/05/89 (Electromagnetic

compatibility) and subsequent amendments;

- 93/68/EEC of 22/07/93 and subsequent amendments;

- 2002/96/EC

Warning: If the hob is fitted above a built-in oven, the hob

and the oven must be connected to the mains separately for

safety reasons and to simplify operations when it is necessary

to pull the oven out for some reason.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston KBM 6001 H IX in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston KBM 6001 H IX Manual

Product: