Manual Hotpoint-Ariston aqlf9d69ua (page 8 of 64) (English, Dutch, French, Italian)

315454

Zoom out

Zoom in

1/64

Running a wash cycle

WARNING: before you use the washing machine for

the first time, run a wash cycle with detergent and no

laundry, using the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the

button.

All the indicator lights will illuminate for 1 second and

the text AQUALTIS will appear on the display; the

indicator light corresponding to the

button will then

remain lit in a constant manner and the START/

PAUSE indicator light will flash.

2. SELECT THE PROGRAMME. Turn the PROGRAMME

KNOB left or right, until the required programme has been

selected; the name of the programme will appear on the

display. A temperature and spin speed is set for each

programme; these may be adjusted. The cycle duration

will also appear on the display.

3. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

4. MEASURE OUT THE DETERGENT. There is no

need to add detergent when the "Auto Dose System"

mode is used, as the machine automatically intakes

detergent on the basis of the selected programme,

type of load and water hardness. Refer to the

paragraph "Traditional mode for implementing the

traditional operation mode.

5. CLOSE THE PORTHOLE DOOR.

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons on the control panel:

Modify the temperature and/or spin speed.

The machine automatically displays the maximum

temperature and spin speed values set for the

selected cycle, or the most recently-used settings if

they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash OFF setting is reached.

The spin speed may be progressively reduced by

pressing the

button, until it is completely excluded

OFF. If these buttons are pressed again, the

maximum values are restored.

 Exception: if the Cottons programme is selected, the

temperature can be increased up to a value of 90°C.

Set a DELAY TIMER.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. During the setting procedure,

the delay period and the text "Starts in:" will be

displayed, along with the flashing

symbol. After the

delayed start has been set, the

symbol will remain

fixed on the display, which will also indicate the duration

of the selected cycle with the text "Ends in:" and the

cycle duration. Press the DELAY TIMER button just

once to display the delay time set previously.

After the countdown has begun, the display will show

the text "Starts in:" and the delay period. Once the set

delay time has elapsed, the machine will begin its cycle

and the display will show "Ends in:" and the time

remaining until the end of the cycle. To remove the

delayed start option, press the button until the display

shows the text OFF; the

symbol will disappear.

Modify the cycle settings.

 Press the button to activate the option; the name

of the option will then appear on the display and

the corresponding indicator light will illuminate.

 Press the button again to deactivate the option;

the name of the option will then appear on the

display followed by the text OFF, and the

corresponding indicator light will switch off.

 If the selected option is not compatible with the

selected wash cycle, this incompatibility will be

signalled by the flashing of the indicator light and a

sound alert (3 beeps); the option will not be activated.

 If the selected option is not compatible with another

option that has been selected previously, the indicator

light corresponding to the first option selected will flash

and only the second option will be activated; the

indicator light corresponding to the button will remain

lit in a constant manner.

 The options may affect the recommended load value and/

or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light

remains lit in a fixed manner and the porthole door

locks (the

DOOR LOCKED indicator light

illuminates). The icons corresponding to the wash

cycle phases will light up during the cycle to indicate

which phase is currently in progress. To change a

wash cycle once it has already started, pause the

washing machine by pressing the START/PAUSE

button; then select the desired cycle and press the

START/PAUSE button again. To open the door during

a wash cycle, press the START/PAUSE button; if the

DOOR LOCKED

indicator light is switched off you

may open the door. Press the START/PAUSE button

again to restart the wash cycle from the point at

which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may be

opened immediately. If the START/PAUSE indicator light

is flashing, press the button to end the cycle. Open the

door, unload the laundry and switch off the machine.

 If you wish to cancel a cycle which has already begun,

press and hold the

button until the cycle stops and

the machine switches off.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to

wash even the most valuable and delicate garments in

complete confidence thanks to the special bag which

protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you

wash quilts and padded items with an outer layer made

using synthetic material.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston aqlf9d69ua in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 3,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston aqlf9d69ua Manual

Product: