71720

Hotpoint-Ariston AQGMD 129 Manual

12
Zoom out
Zoom in
Previous page
1/28
Next page
GB
12
Troubleshooting
Possible causes / Solutions:
The plug has not been inserted into the electrical socket, or it has not
been inserted far enough to make contact.
There is no power in the house.
The porthole door has not been shut properly.
The START/PAUSE button has not been pressed.
The water tap has not been turned on.
The water inlet hose is not connected to the tap.
The hose is kinked.
The water tap has not been turned on.
There is no water in the house.
The water pressure is insufficient.
The START/PAUSE button has not been pressed.
The end of the outlet hose has not been fitted at a height between 65
and 100 cm from the floor (see Installation).
The free end of the hose is underwater (see Installation).
If If the dwelling is on one of the upper floors of a building, there may be
problems relating to water drainage, causing the washer-dryer to load
and drain water continuously. Special anti-draining valves are available in
shops and help to avoid this inconvenience.
The water drainage systemis not fitted with a breather pipe.
The programme does not include a draining phase: some programmes
require manual draining (see Programmes and options).
The Easy Iron option is enabled: to complete the programme, press
the START/PAUSE button (see Programmes and options).
The outlet hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked properly when the appliance was installed (see Installation).
The washer-dryer is not level (see Installation).
The washer-dryer is trapped between cabinets and a wall (see Installation).
The load is not balanced properly (see Description of the machine).
The water inlet hose is not screwed on to the tap correctly (see Installation).
The detergent dispenser drawer is blocked (for instructions on how to
clean it, see Care and maintenance).
The outlet hose has not been secured properly (see Installation).
Switch off the machine and unplug the appliance; wait for approximately
1 minute then switch it on again.
If the problem persists, contact Assistance.
The detergent is not designed for machine washing (the packaging should state that
the product is for washing by machine, for washing by hand or machine or similar).
Too much detergent was used.
Follow the manual unlocking procedure (see Precautions and tips).
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A delayed start has been set.
The DRYING cycle is on the OFF setting.
From time to time your machine may not operate as it should. Before calling for Assistance (see Assistance),
make sure that the problem cannot be resolved easily using the following list.
Malfunction:
The washer-dryer
will not switch on.
The wash cycle
does not begin.
The washer-dryer fails to fill
with water.
The machine continuously fills
and drains water.
The washer-dryer does not
drain or spin.
The washer-dryer vibrates
too much during the spin cycle.
The washer-dryer leaks.
The icons corresponding to the Phase
in progress flash rapidly at the same
time as the ON/OFF indicator light.
There is too much foam.
The washer-dryer door remains locked.
The washer-dryer does not dry.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint-Ariston AQGMD 129 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston AQGMD 129 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info