71720

Hotpoint-Ariston AQGMD 129 Manual

2
Zoom out
Zoom in
Previous page
1/28
Next page
GB
2
Installation
A
Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given away
or moved, please ensure the manual remains with the
machine so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully it
contains important information regarding the safe
installation, use and maintenance of the appliance.
You will find the guarantee and other details relating to
the installation process in the bag containing this booklet.
Unpacking and levelling
Unpacking
1. Once the washer-dryer has been removed from the
packaging, check that it has not been damaged
during transportation.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
2. Remove the 4
protective screws used
during transportation and
the corresponding
spacers on the back of
the machine (see figure).
3. Close the holes using the plastic covers provided in
the bag.
4. Keep all the pieces; if the washer-dryer is
transported in future, the screws and spacers will
have to be replaced in order to avoid damaging the
inside of the machine.
Packaging materials should not be used as toys by
children.
Levelling
1. Position the washer-dryer on a level and sturdy
floor, without resting it against walls or cabinets.
2. If the floor is uneven,
the feet of the appliance
may be adjusted until it
reaches a perfectly
horizontal position (the
angle of inclination must
not exceed 2 degrees).
If the appliance is levelled correctly it will be more
stable and much less likely to cause vibrations and
noise during the spin cycle.
If positioned on a fitted carpet or a rug, adjust the
feet in such a way as to allow room for air to circulate
and provide ventilation beneath the washer-dryer.
Connecting the water and electricity
supplies
Connecting the water inlet hose
Before connecting the inlet hose to the water supply, allow
the water to flow from the tap until it runs clear.
1. Connect the inlet hose
to the machine, by
screwing it into the cold
water inlet on the upper
right hand side of the
back of the machine (see
figure).
2. Place the seal A
(provided in the bag) on
the end of the inlet hose
and screw it to a cold
water tap with a 3/4 gas
threaded connection (see
figure).
3. The hose should not be bent or compressed.
The water pressure at the tap must fall within the
values indicated in the Technical data table (see next
page).
If the inlet hose is not long enough, contact a
specialist store or an authorised technician.
Always use the new inlet hoses supplied with the
machine.
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint-Ariston AQGMD 129 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston AQGMD 129 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info