Manual Hotpoint-Ariston AQD1170D 697 I AQUALTIS (page 8 of 16) (English)

630453

Zoom out

Zoom in

1/16

WARNING: before you use the Washer-dryer for the first time,

run a wash cycle with detergent and no laundry, using the 90°

cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the button. All

the indicator lights will illuminate for 1 second and the text

AQUALTIS will appear on the display; the indicator light

corresponding to the button will then remain lit in a constant

manner and the START/PAUSE indicator light will flash.

2. SELECT THE PROGRAMME. Turn the PROGRAMME

KNOB left or right, until the required programme has been

selected; the name of the programme will appear on the

display. A temperature and spin speed is set for each

programme; these may be adjusted. The cycle duration will

also appear on the display.

3. LOAD THE LAUNDRY. Open the porthole door. Load the

laundry, making sure you do not exceed the maximum load value

indicated in the table of wash cycles on the following page.

4. MEASURE OUT THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Description of the machine”.

5. CLOSE THE PORTHOLE DOOR.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons on the control panel:

Modify the temperature and/or spin speed.

The machine automatically displays the maximum temperature

and spin speed values set for the selected cycle, or the most

recently-used settings if they are compatible with the selected

cycle. The temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached. The

spin speed may be progressively reduced by pressing the

button, until it is completely excluded “OFF”. If these buttons

are pressed again, the maximum values are restored.

Setting the drying cycle.

The first time the button is pressed, the machine will

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent presses

will decrease the drying level and then the drying time, until

the cycle is excluded completely (“OFF”). If these buttons are

pressed again, the maximum values are restored.

Drying may be set as follows:

A - Based on a set time period: between 20 and 180 minutes.

B- Based on the desired laundry dryness level:

Iron: suitable for clothes which will need ironing afterwards.

the remaining dampness softens creases, making them

easier to remove.

Hanger: ideal for clothes which do not need to be dried fully.

Cupboard: suitable for laundry which can be put back in a

cupboard without being ironed.

Extra: suitable for garments which need to be dried

completely, such as sponges and bathrobes.

If your laundry load to be washed and dried is much greater

than the maximum stated load, perform the wash cycle,

and when the cycle is complete, divide the garments into

groups and put some of them back in the drum. At this

point, follow the instructions provided for a “Drying only”

cycle. Repeat this procedure for the remainder of the load.

A cooling-down period is always added to the end of each

drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle ( - - )

in accordance with the type of fabric. The desired drying level or

time may also be set using the DRYING button .

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay period has

been reached. During the setting procedure, the delay period and

the text “Starts in:” will be displayed, along with the flashing

symbol. After the delayed start has been set, the symbol

will remain fixed on the display, which will also indicate the

duration of the selected cycle with the text “Ends in:” and the

cycle duration. Press the DELAYED START button just once to

display the delay time set previously. After the countdown has

begun, the display will show the text “Starts in:” and the delay

period. Once the set delay time has elapsed, the machine will

begin its cycle and the display will show “Ends in:” and the time

remaining until the end of the cycle. To remove the delayed start

option, press the button until the display shows the text OFF;

the symbol will disappear.

Modify the cycle settings.

• Press the button to activate the option; the name

of the option will then appear on the display and the

corresponding indicator light will illuminate.

• Press the button again to deactivate the option; the

name of the option will then appear on the display

followed by the text OFF, and the corresponding

indicator light will switch off.

! If the selected option is not compatible with the selected

wash cycle, this incompatibility will be signalled by the

flashing of the indicator light and a sound alert

(3 beeps); the option will not be activated.

! If the selected option is not compatible with another

option that has been selected previously, the indicator light

corresponding to the first option selected will flash and

only the second option will be activated; the indicator light

corresponding to the button will remain lit in a constant manner.

! The options may affect the recommended load value and/

or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light remains lit in a fixed

manner and the porthole door locks (the LOCK indicator

light illuminates). The icons corresponding to the wash cycle

phases will light up during the cycle to indicate which phase

is currently in progress. To change a wash cycle once it has

already started, pause the Washer-dryer by pressing the

START/PAUSE button; then select the desired cycle and

press the START/PAUSE button again. To open the door

during a wash cycle, press the START/PAUSE button; if the

LOCK indicator light is switched off you may open the

door. Press the START/PAUSE button again to restart the

wash cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated by

the illuminated text END. The porthole door may be opened

immediately. If the START/PAUSE indicator light is flashing,

press the button to end the cycle. Open the door, unload

the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the button until the cycle stops and the machine

switches off.

How to run a wash cycle or a

drying cycle

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston AQD1170D 697 I AQUALTIS in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston AQD1170D 697 I AQUALTIS Manual

Product: