Manual Hotpoint-Ariston AQD1071D 69 AQUALTIS (page 2 of 72) (English, German, Dutch, French, Portuguese, Spanish)

570651

2

Zoom out

Zoom in

Previous page

1/72

Next page

EN

2

Installation

! This instruction manual should be kept in a

safe place for future reference. If the Washer-

dryer is sold, given away or moved, please

ensure the manual is kept with the machine,

so that the new owner may benefit from the

advice contained within it.

! Read these instructions carefully: they

contain vital information relating to the safe

installation and operation of the appliance.

! Inside the pack containing this manual, you

will also find the guarantee and all the details

necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging

from the Washer-dryer, make sure it has not

been damaged during transportation.

If it has been damaged, contact the retailer

and do not proceed any further with the

installation process.

2. Remove the 4

protective screws

(used during

transportation) and

the corresponding

spacer, located on

the rear part of the

appliance (see figure).

3. Close off the holes using the plastic plugs

supplied in the pack.

4. Keep all the parts in a safe place; they will

be needed again if the Washer-dryer is moved

to another location, to prevent the inside of the

appliance being damaged.

! Packaging materials should not be used as

toys for children.

Levelling

1. Place the Washer-

dryer on a flat sturdy

floor, without resting

it up against walls or

cabinets.

2. If the floor is

uneven, the front feet

of the machine may

be adjusted until it

reaches a horizontal

position (the angle of

inclination must not exceed 2 degrees).

! If the appliance is levelled correctly, it will

be more stable and much less likely to cause

vibrations and noise while it is operating,

particularly during the spin cycle.

! If it is placed on carpet or a rug, adjust the

feet in such a way as to allow a sufficient

ventilation space underneath the Washer-dryer.

Connecting the electricity and

water supplies

Connecting the water inlet hose

! Before connecting the inlet hose to the water

supply, run the water until it is perfectly clear.

1. Connect the inlet

hose to the machine

by screwing it onto

the cold water inlet of

the appliance, which

is situated on the top

right-hand side of

the rear part of the

appliance (see figure).

2. Connect the inlet

hose by screwing it to

a cold water tap using

a 3/4 gas threaded

connection (see

figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical data table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

1

We have two Hotpoint Ariston Aqualtis AQD1071D 69 washer/dryers. Both have the same issue, they automatically start a new program (within ~5 mins) after the original one ended. So, unless we're waiting near the washer -- to end it manually -- it restarts the program, and spoils water and heat.
Additionally, both of them give the error "No water check supply" while in the 'middle' of certain programs. There does not seem to be real problem with the water supply, water is used in other parts of the programs, and if we ignore the error,the program just continues after a few minutes (and will automatically start a new program when done :)) Submitted on 4-3-2017 at 14:38
Reply Report abuse
- Ow, sorry, my question is if anybody has any idea on what creates this problem, and how this might be fixed? Answered on 4-3-2017 at 14:51
  Vote up Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Hotpoint-Ariston AQD1071D 69 AQUALTIS at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston AQD1071D 69 AQUALTIS in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 8,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info